Re: Servo drives- Mariss Rutex PID and Tuning with a O-Scope
Posted by
Mariss Freimanis
on 2005-05-12 22:58:17 UTC
Tuned or mistuned, a servo will arrive at the correct place. All
tuning does is optimize the settling time. This for most applications
is of little consequence.
Rutex is a competitor to our drives but I can say nothing bad about
them because they have always been a fair and honest competitor. Like
us, they build good drives at a good price.
There are people that prefer them just as there are people that
prefer our drives to theirs. It's a Coke versus a Pepsi kind of
thing. I'd rather not be goaded into putting a fair and good
competitor into a bad light. The world is big enough for the likes of
us and them and a dozen more.
Mariss
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<dave_mucha@y...> wrote:
tuning does is optimize the settling time. This for most applications
is of little consequence.
Rutex is a competitor to our drives but I can say nothing bad about
them because they have always been a fair and honest competitor. Like
us, they build good drives at a good price.
There are people that prefer them just as there are people that
prefer our drives to theirs. It's a Coke versus a Pepsi kind of
thing. I'd rather not be goaded into putting a fair and good
competitor into a bad light. The world is big enough for the likes of
us and them and a dozen more.
Mariss
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<dave_mucha@y...> wrote:
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Alan Marconett"<KM6VV@a...>
> wrote:gather
> > Hi Dave,
> >
> > What's this about PID tuning? What are the inputs to the 'scope?
> Some sort
> > of encoder or tach on the shaft? Plus some display of the input
> commands?
> >
> > Alan KM6VV
>
>
> I took a brief look at the Rutex site and they claim a faster and
> better PID for more stable control. Faster than what?? I think than
> their old one ?
>
> They show a screen shot of the stable motor operation. And, I
> that screen is from the software monitoring the motor paramters ?about
>
> Also, the people who have po-poo'd G-320's seem to all complain
> tuning. (one was upset that he couldn't tune it without having toit.
> spend the extra $$ for an encoder) but also, everyone who has used a
> scope to tune them speaks highly of the drive.
>
> Since there are a few pc-scope free-ware programs, I assumed that
> people are using them to tune the servo drives, and that being the
> case, I also assumed that someone would have done a "ho-to" about
>
> I also assume that 90% of the people tune them quickly and easily or
> at least satisfactorily, from the methods at hand.
>
> Dave
Discussion Thread
turbulatordude
2005-05-12 18:52:17 UTC
Re: Servo drives- Mariss Rutex PID and Tuning with a O-Scope
KM6VV
2005-05-12 19:50:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss Rutex PID and Tuning with a O-Scope
Mariss Freimanis
2005-05-12 22:58:17 UTC
Re: Servo drives- Mariss Rutex PID and Tuning with a O-Scope
Alan Marconett
2005-05-13 10:23:16 UTC
RE: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss Rutex PID and Tuning with a O-Scope
Mcginnis, Darrell S
2005-05-17 16:37:08 UTC
RE: [CAD_CAM_EDM_DRO] Re: Servo drives- Mariss Rutex PID and Tuning with a O-Scope