Re: [CAD_CAM_EDM_DRO] weird motor problem on my cnc mill
Posted by
Bob Muse
on 2005-07-09 15:11:10 UTC
Hi Rick
Do your servo amps take an analog command signal such as 0-10V? Maybe with
tach feedback? Seems like I have had a similar problem when the gain and
offset pots on the servo amp were not adjusted properly. I used a precision
voltage reference box hooked to the command input on the servo amp to adjust
and balance the amps.
Bob
Do your servo amps take an analog command signal such as 0-10V? Maybe with
tach feedback? Seems like I have had a similar problem when the gain and
offset pots on the servo amp were not adjusted properly. I used a precision
voltage reference box hooked to the command input on the servo amp to adjust
and balance the amps.
Bob
----- Original Message -----
From: "skykotech" <rick@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Saturday, July 09, 2005 10:11 AM
Subject: [CAD_CAM_EDM_DRO] weird motor problem on my cnc mill
> I am experiencing a strange problem on my x axis motor on my cnc
> mill. The motor is a Fanuc 0, 56V DC brush, 4 pole. One direction
> the motor runs smooth, the other direction it growls and shudders.
> I took out each of the four brushes and they look perfect. Peering
> at the commutators, they look perfect too. The bearings *feel* ok
> when you turn the shaft of the motor either direction by hand. I
> ran the motor off of a 1 volt supply and it spins in both directions
> without stalling.
>
> On the mill, running it with a gecko g340 drive, the direction
> changes from cw to ccw are harsh (but strangly smooth from ccw to
> cw). At certain speeds in the ccw direction, there is a shuddering
> of the motor, but not in the cw direction.
>
> Any ideas what could be the culprit? If you can even find a used
> Fanuc 0 motor on ebay, they run $200 to $500 in unknown condition...
>
> Thanks for any help
>
> Rick
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
Discussion Thread
skykotech
2005-07-09 10:11:10 UTC
weird motor problem on my cnc mill
Ed Fanta
2005-07-09 12:00:11 UTC
Re: [CAD_CAM_EDM_DRO] weird motor problem on my cnc mill
Bob Muse
2005-07-09 15:11:10 UTC
Re: [CAD_CAM_EDM_DRO] weird motor problem on my cnc mill
skykotech
2005-07-09 20:45:44 UTC
Re: weird motor problem on my cnc mill
R Rogers
2005-07-09 21:17:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: weird motor problem on my cnc mill
skykotech
2005-07-09 22:48:27 UTC
Re: weird motor problem on my cnc mill