Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Posted by
johndroc@a...
on 2000-06-28 21:34:50 UTC
Jon,
Thank you, very much, for the information. I was able to get the X-axis
working today - properly. I had incorrect settings for Output Scale and
Max_Velocity; after I set those I achieved oscillation in the table, I
tweaked the Tach and Signal adjustments a few times, and it seemed to be
roughly tuned. I think the Y amp is dead, I surmised it before and switched
the X and Y amps - now X works and Y doesn't. It has a tendency to "slam"
into the -Y. I don't know if I'll be able to find any ServoDynamics(?)
replacement parts; that will be the next challenge. I'll switch out the Y
and Z next, to see if the Z board works on Y. Thanks again.
-John
Thank you, very much, for the information. I was able to get the X-axis
working today - properly. I had incorrect settings for Output Scale and
Max_Velocity; after I set those I achieved oscillation in the table, I
tweaked the Tach and Signal adjustments a few times, and it seemed to be
roughly tuned. I think the Y amp is dead, I surmised it before and switched
the X and Y amps - now X works and Y doesn't. It has a tendency to "slam"
into the -Y. I don't know if I'll be able to find any ServoDynamics(?)
replacement parts; that will be the next challenge. I'll switch out the Y
and Z next, to see if the Z board works on Y. Thanks again.
-John
Discussion Thread
Jon Elson
2000-06-24 22:09:19 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-25 06:56:38 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-25 22:30:25 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-26 06:50:08 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-26 12:01:43 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-26 19:01:13 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-27 10:36:50 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-28 21:34:50 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-28 21:57:42 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Matt Shaver
2000-06-28 22:16:47 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-29 06:14:49 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-29 20:39:48 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-29 23:04:47 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-30 05:35:04 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-30 11:28:13 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Darrell
2000-06-30 12:25:33 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.