Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Posted by
Jon Elson
on 2000-06-28 21:57:42 UTC
johndroc@... wrote:
pretty
pedestrian, although they may use power fets with Japanese numbers.
A tach problem, tach phasing or motor phasing could also cause the axis
runaway
problem.
Anyway, sounds like real progress!
Jon
> Jon,These are Servo Dynamics amps? What model? The major parts in it are
>
> Thank you, very much, for the information. I was able to get the
> X-axis
> working today - properly. I had incorrect settings for Output Scale
> and
> Max_Velocity; after I set those I achieved oscillation in the table, I
>
> tweaked the Tach and Signal adjustments a few times, and it seemed to
> be
> roughly tuned. I think the Y amp is dead, I surmised it before and
> switched
> the X and Y amps - now X works and Y doesn't. It has a tendency to
> "slam"
> into the -Y. I don't know if I'll be able to find any
> ServoDynamics(?)
> replacement parts; that will be the next challenge. I'll switch out
> the Y
> and Z next, to see if the Z board works on Y. Thanks again.
pretty
pedestrian, although they may use power fets with Japanese numbers.
A tach problem, tach phasing or motor phasing could also cause the axis
runaway
problem.
Anyway, sounds like real progress!
Jon
Discussion Thread
Jon Elson
2000-06-24 22:09:19 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-25 06:56:38 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-25 22:30:25 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-26 06:50:08 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-26 12:01:43 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-26 19:01:13 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-27 10:36:50 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-28 21:34:50 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-28 21:57:42 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Matt Shaver
2000-06-28 22:16:47 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-29 06:14:49 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-29 20:39:48 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-29 23:04:47 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
johndroc@a...
2000-06-30 05:35:04 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Jon Elson
2000-06-30 11:28:13 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.
Darrell
2000-06-30 12:25:33 UTC
Re: [CAD_CAM_EDM_DRO] Servo amplifier boards.