CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] EMC in Portland

Posted by Tim Goldstein
on 2000-07-05 06:41:32 UTC
If you are familiar with Linux, EMC is not hard to set up. The big
difficulty people have is getting the RT kernel running and that is mostly a
matter of reading the instructions and following it exactly (something we
men tend not to do to well).

I am Running EMC with steppers and can get speeds to about 90 ipm. I don't
run that fast as I have a resonance at about 54 ipm on my Y axis, but I
think that is caused by my driver/motors/machine not by EMC. The 90 ipm top
end I am seeing I think is caused by my 36 V power supply. I think If I were
to move to a driver that used higher voltage I would have more top end, so
again not an EMC limitation.

Yes, you can set up Linux/EMC so that you can copy files on the network. I
am running mine with the SAMBA server and can read/delete/add files on the
Linux box from any 3.1WFW, 9X, NT, Win 2000 Windows system on my network.

Tim
[Denver, CO]

> -----Original Message-----
> From: Donn Busby [mailto:donn@...]
> Sent: Wednesday, July 05, 2000 12:45 AM
> To: CAD_CAM_EDM_DRO@egroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] EMC in Portland
>
>
> I appreciate the offers.
>
> Darrell in Washington was kind enough to give me a call, and I got the
> impression from him that EMC is not easily setup to run stepper motors at
> rapid feed rates, i.e. 40ipm to 150ipm which is the range I run.
>
> I have access to or own several versions of Linux, including the version
> that seems popular, Redhat 5.2. Because of time constraints and
> the need to
> focus on what is working for me right now I haven't put any
> energy into even
> getting that going. Since I am pretty well versed in computers and have
> been involved with them from DOS days, I feel I could probably
> get a system
> up and running especially with the work that has gone before in
> this group.
> Though, if what Darrell says is accurate, then I will probably wait until
> there is enough development in EMC that I have a possibility of getting it
> to do what I want.
>
> My present set up is a CNC Crafter 14" X 20" X 3"Z with 300 ounce
> steppers.
> I run it with the Buckhannon CNC controller for machine control and Bobcad
> for G code generation or CorelDraw with the HPGL interpreter running the
> machine. I have a computer dedicated to running the router and another
> that I design with and transfer files from.
>
> One of the reasons I am frustrated with my present system is that I am
> unable to send files to the CNC controller without either using a
> floppy to
> transfer files or booting back into Win98, transfering the files,
> then back
> to DOS to run the program. Is my impression correct that I can network my
> Win98 system directly with Linux?
>
> Donn
> donn@...
> http://www.bridgecitysystems.com - Computers & Consulting
> http://www.cnc-works.com - CNC Crafts, Engraving & Precision Routing
>

Discussion Thread

Donn Busby 2000-07-02 20:26:35 UTC EMC in Portland Tim Goldstein 2000-07-02 20:41:15 UTC RE: [CAD_CAM_EDM_DRO] EMC in Portland Donn Busby 2000-07-04 23:47:13 UTC Re: [CAD_CAM_EDM_DRO] EMC in Portland Tim Goldstein 2000-07-05 06:41:32 UTC RE: [CAD_CAM_EDM_DRO] EMC in Portland Jeff Demand 2000-07-05 06:53:38 UTC Re: [CAD_CAM_EDM_DRO] EMC in Portland Tim Goldstein 2000-07-05 07:15:09 UTC RE: [CAD_CAM_EDM_DRO] EMC in Portland Ian Wright 2000-07-05 10:38:54 UTC Re: [CAD_CAM_EDM_DRO] EMC in Portland Ejay Hire 2000-07-05 13:39:27 UTC RE: [CAD_CAM_EDM_DRO] EMC in Portland Jon Elson 2000-07-05 13:43:47 UTC Re: [CAD_CAM_EDM_DRO] EMC in Portland Ian Wright 2000-07-06 03:43:40 UTC Re: [CAD_CAM_EDM_DRO] EMC in Portland Ron Ginger 2000-07-06 05:32:23 UTC Re: [CAD_CAM_EDM_DRO] EMC in Portland Tim Goldstein 2000-07-06 06:47:02 UTC RE: [CAD_CAM_EDM_DRO] EMC in Portland Jon Elson 2000-07-06 12:08:53 UTC Re: [CAD_CAM_EDM_DRO] EMC in Portland