CAD CAM EDM DRO - Yahoo Group Archive

W.E.T.??: [CAD_CAM_EDM_DRO] Re: motor sizing vertical slide EDM

Posted by ballendo
on 2006-05-14 15:45:06 UTC
Hello,

Were I you; I'd look to proven solutions used in commercial cnc
machines of all sizes...

BP's use an air cylinder to balance the knee.

Bigger machines--like the CINCY I retro'd--use a hydraulic cylinder
to do the same thing. But it's the head, not the knee.

Even small machines like the sieg minimill use a gas shock...

Commercial routers like a Gerber Sabre use springs...

There must be a reason these folks didn't use a counterweight?!?
(Actually several reasons, IMO.)

Hope this helps,

Ballendo

--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@...> wrote:
>
> wthomas@... wrote:
>
> >Hi Jon, Marcus and All:
> > This is a very interesting discussion to me as I was
thinking of
> >putting such a counterweight on the head of a bed mill and the
effect
> >that it would have when pick drilling. What would happen if the
> >counterweight had through holes in it and set in a container of
90
> >weight oil? Do you think the oil would dampen it enough or am I
> >dreaming?
> >
> >
> I suspect this would work very well. If oil can't do it, grease
> certainly would.
>
> Jon
>

Discussion Thread

tomp-tag 2006-05-10 11:11:08 UTC motor sizing vertical slide EDM Graham Stabler 2006-05-10 15:02:43 UTC Re: motor sizing vertical slide EDM Mariss Freimanis 2006-05-10 16:23:36 UTC Re: motor sizing vertical slide EDM Marcus 2006-05-10 19:53:52 UTC Re: [CAD_CAM_EDM_DRO] motor sizing vertical slide EDM tomp-tag 2006-05-11 06:51:51 UTC RE: motor sizing vertical slide EDM tomp-tag 2006-05-11 07:58:55 UTC Re: motor sizing vertical slide EDM Marcus 2006-05-11 08:09:42 UTC Re: [CAD_CAM_EDM_DRO] RE: motor sizing vertical slide EDM Mariss Freimanis 2006-05-11 08:54:51 UTC Re: motor sizing vertical slide EDM Graham Stabler 2006-05-11 09:34:00 UTC Re: motor sizing vertical slide EDM tomp-tag 2006-05-12 14:05:31 UTC Re: motor sizing vertical slide EDM tomp-tag 2006-05-12 14:41:05 UTC Re: motor sizing vertical slide EDM tomp-tag 2006-05-12 14:43:19 UTC Re: motor sizing vertical slide EDM tomp-tag 2006-05-12 14:46:08 UTC Re: motor sizing vertical slide EDM tomp-tag 2006-05-12 14:46:27 UTC Re: motor sizing vertical slide EDM tomp-tag 2006-05-12 14:52:24 UTC Re: motor sizing vertical slide EDM Graham Stabler 2006-05-12 15:22:22 UTC Re: motor sizing vertical slide EDM Mariss Freimanis 2006-05-12 18:06:56 UTC Re: motor sizing vertical slide EDM Jon Elson 2006-05-13 09:27:37 UTC Re: [CAD_CAM_EDM_DRO] Re: motor sizing vertical slide EDM Graham Stabler 2006-05-13 12:59:52 UTC Re: motor sizing vertical slide EDM Marcus 2006-05-13 19:27:50 UTC Re: [CAD_CAM_EDM_DRO] Re: motor sizing vertical slide EDM wthomas@g... 2006-05-13 20:21:17 UTC W.E.T.??: [CAD_CAM_EDM_DRO] Re: motor sizing vertical slide EDM John Dammeyer 2006-05-13 23:00:01 UTC Bender question wthomas@g... 2006-05-14 00:10:27 UTC W.E.T.Re: [CAD_CAM_EDM_DRO] Bender DRO question some OT ballendo 2006-05-14 04:18:30 UTC Re: Bender question (long reply) Wayne Weedon 2006-05-14 05:34:23 UTC Re: W.E.T.??: [CAD_CAM_EDM_DRO] Re: motor sizing vertical slide EDM turbulatordude 2006-05-14 06:17:23 UTC Re: Bender question (long reply) John Dammeyer 2006-05-14 10:39:39 UTC RE: [CAD_CAM_EDM_DRO] Re: Bender question (long reply) Marcus 2006-05-14 12:39:51 UTC Re: W.E.T.??: [CAD_CAM_EDM_DRO] Re: motor sizing vertical slide EDM ballendo 2006-05-14 14:00:33 UTC No add photos button?!? wasRe: Bender question (long reply) Graham Stabler 2006-05-14 14:06:44 UTC No add photos button?!? wasRe: Bender question (long reply) ballendo 2006-05-14 14:16:20 UTC 3-in-1 back gauge photos at DIY-CNC was Re: Bender question (long reply) ballendo 2006-05-14 14:18:12 UTC Re: Bender question (long reply) John Dammeyer 2006-05-14 14:54:29 UTC RE: [CAD_CAM_EDM_DRO] Re: Bender question (long reply) ballendo 2006-05-14 14:58:49 UTC OT thank you re No add photos button?!? wasRe: Bender question (long reply) Jon Elson 2006-05-14 15:02:32 UTC Re: W.E.T.??: [CAD_CAM_EDM_DRO] Re: motor sizing vertical slide EDM ballendo 2006-05-14 15:22:20 UTC Re: Bender question (long reply) ballendo 2006-05-14 15:33:56 UTC Re: Bender question (long reply) ballendo 2006-05-14 15:38:28 UTC ELS? was Re: Bender question ballendo 2006-05-14 15:45:06 UTC W.E.T.??: [CAD_CAM_EDM_DRO] Re: motor sizing vertical slide EDM wthomas@g... 2006-05-14 17:14:45 UTC Re:W.E.T. [CAD_CAM_EDM_DRO] Re: Bender question (long reply) John Dammeyer 2006-05-14 19:59:30 UTC RE: [CAD_CAM_EDM_DRO] ELS? (long answer) BobWarfield 2006-05-15 15:47:52 UTC Re: Bender question ballendo 2006-05-15 16:52:29 UTC Re: Bender question wthomas@g... 2006-05-15 22:22:35 UTC W.E.T. [CAD_CAM_EDM_DRO] Re: Bender question tomp-tag 2006-05-16 14:48:18 UTC Re: motor sizing vertical slide EDM