Re: Agilent Encoder Pull-up resistor
Posted by
afogassa
on 2006-08-15 16:41:01 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "shadi_salhab_78"
<salhab@...> wrote:
pcb to the motor is over 1 foot or so, rutex has a pcb that
converters the signal from incremental encoders to differential it's
about 20Us$ or so.
After installing the converter don't use pullup resistors.
I'm using rutex drives and it's very good, little hard to tune it
with software, I like the old ones with pots to set it up.
Fogassa
<salhab@...> wrote:
>pulses
> Hi all ,
> I've installed an Agilent Encoder HEDS 5500 on a servo motor to
> conunnicate with rutex drive , the problem is that it only read
> on very low RPM , if I rise RPM it stops reading , I have put adrive
> pull-up resistor mentioned in Agilent data sheet, the result is
> reads at a higher RPM, I kept increasing the pull-up resistor valueencoders
> until I reached 4K ohm each but no more then 600 RPM , which is not
> sufficient , is it supposed to be the situation with Agilent
> ? or there is some problem with the encoder? Should I try to useRutex new drives needs differential encoders if the distance from
> differential encoders?
>
>
> Thanks,
>
> Shadi
>
pcb to the motor is over 1 foot or so, rutex has a pcb that
converters the signal from incremental encoders to differential it's
about 20Us$ or so.
After installing the converter don't use pullup resistors.
I'm using rutex drives and it's very good, little hard to tune it
with software, I like the old ones with pots to set it up.
Fogassa
Discussion Thread
shadi_salhab_78
2006-08-14 11:59:13 UTC
Agilent Encoder Pull-up resistor
Wayne Weedon
2006-08-14 13:43:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Agilent Encoder Pull-up resistor
leotata
2006-08-15 09:35:15 UTC
Re: Agilent Encoder Pull-up resistor
afogassa
2006-08-15 16:41:01 UTC
Re: Agilent Encoder Pull-up resistor
Jon Elson
2006-08-15 18:30:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Agilent Encoder Pull-up resistor
caudlet
2006-08-15 19:14:13 UTC
Re: Agilent Encoder Pull-up resistor
Peter Homann
2006-08-15 21:01:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Agilent Encoder Pull-up resistor
Jon Elson
2006-08-15 21:34:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Agilent Encoder Pull-up resistor
Mariss Freimanis
2006-08-15 21:54:40 UTC
Re: Agilent Encoder Pull-up resistor
Les Newell
2006-08-16 01:07:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Agilent Encoder Pull-up resistor
Steve Stallings
2006-08-16 05:27:26 UTC
Re: Agilent Encoder Pull-up resistor
Dave Pope
2006-08-16 09:01:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Agilent Encoder Pull-up resistor
Jon Elson
2006-08-16 09:53:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Agilent Encoder Pull-up resistor
Dennis Schmitz
2006-08-16 11:13:40 UTC
Re: Agilent Encoder Pull-up resistor
afogassa
2006-08-16 14:36:15 UTC
Re: Agilent Encoder Pull-up resistor
Jon Elson
2006-08-16 19:27:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Agilent Encoder Pull-up resistor