Re: [CAD_CAM_EDM_DRO] Acad 2002
Posted by
Charles Anderson
on 2006-10-22 21:20:15 UTC
Hey Harko,
Could you do a test render for me following these instructions (I'm on
the verge of writing my own application or buying an add-on for
Lightwave for $1000 US... I'd prefer not to do either).
Instructions:
Make three long thin rectangles coloured red.
Make two long thin rectangles coloured green.
Starting with red alternately lay them on top of each other.
Twist the object, so that you end up with a twisted bar.
Make the bar into a flattened rectangle.
Bisect the rectangle 45 degrees along its length.
Lay the cut rectangle so that the cut is exposed.
What is the result?
Lightwave can't handle this, just wondering if Rhino3D can.
Regards Charles
Harko Schwartz wrote:
Could you do a test render for me following these instructions (I'm on
the verge of writing my own application or buying an add-on for
Lightwave for $1000 US... I'd prefer not to do either).
Instructions:
Make three long thin rectangles coloured red.
Make two long thin rectangles coloured green.
Starting with red alternately lay them on top of each other.
Twist the object, so that you end up with a twisted bar.
Make the bar into a flattened rectangle.
Bisect the rectangle 45 degrees along its length.
Lay the cut rectangle so that the cut is exposed.
What is the result?
Lightwave can't handle this, just wondering if Rhino3D can.
Regards Charles
Harko Schwartz wrote:
>Hi,
>
>Use Rhino3d it is easier to do solids.
>
>Harko
>
>
>
Discussion Thread
Terry Owens
2006-10-22 17:34:37 UTC
Acad 2002
Harko Schwartz
2006-10-22 18:14:43 UTC
Re: [CAD_CAM_EDM_DRO] Acad 2002
Terry Owens
2006-10-22 18:54:09 UTC
Re: [CAD_CAM_EDM_DRO] Acad 2002
Charles Anderson
2006-10-22 21:20:15 UTC
Re: [CAD_CAM_EDM_DRO] Acad 2002
John Dammeyer
2006-10-23 00:26:11 UTC
RE: [CAD_CAM_EDM_DRO] Acad 2002
Terry Owens
2006-11-06 05:54:04 UTC
Re: [CAD_CAM_EDM_DRO] Acad 2002
Darren Lucke
2006-11-06 06:38:41 UTC
Re: [CAD_CAM_EDM_DRO] Acad 2002
Brian Worth
2006-11-06 12:13:32 UTC
Re: [CAD_CAM_EDM_DRO] Acad 2002
Terry Owens
2006-11-06 15:36:01 UTC
Re: [CAD_CAM_EDM_DRO] Acad 2002
Mariss Freimanis
2006-11-06 19:34:10 UTC
Re: Acad 2002
Terry Owens
2006-11-07 09:59:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Acad 2002
JanRwl@A...
2006-11-07 10:20:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Acad 2002
Terry Owens
2006-11-07 14:17:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Acad 2002
Lester Caine
2006-11-08 00:06:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Acad 2002
aball_2006
2006-11-09 09:26:24 UTC
Re: Acad 2002
Terry Owens
2006-11-09 12:22:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Acad 2002
bamse5619
2006-11-09 19:15:02 UTC
Re: Acad 2002
Fred Smith
2006-11-10 00:17:27 UTC
Re: Acad 2002
Terry Owens
2006-11-10 08:13:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Acad 2002