Re: [CAD_CAM_EDM_DRO] Re: Need to commission a job
Posted by
Justin .
on 2006-11-18 14:43:39 UTC
Hi Dave
Thanks for that! Anyway, for that online shope thing
you need to have Windows. Since Microsoft seem to be
so unethical, I try to steer clear of them. I have
linux. But that site won't even handle Mac let alone
linux! (You have to download a Windoze only program).
I'll try that group then - see what they have to say.
Cheers
Justin
--- turbulatordude <dave_mucha@...> wrote:
Do you Yahoo!?
Everyone is raving about the all-new Yahoo! Mail beta.
http://new.mail.yahoo.com
Thanks for that! Anyway, for that online shope thing
you need to have Windows. Since Microsoft seem to be
so unethical, I try to steer clear of them. I have
linux. But that site won't even handle Mac let alone
linux! (You have to download a Windoze only program).
I'll try that group then - see what they have to say.
Cheers
Justin
--- turbulatordude <dave_mucha@...> wrote:
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, pandya amit____________________________________________________________________________________
> <amitpandyain@...>
> wrote:
> >
> >
> > Hello Justin!
> >
> > Why don't you try www.emachineshop.com ? I bet
> you
> > will thank me for suggesting their name, after
> > completing your project :-)
> >
>
>
> He may, but his wallet may not. :)
>
> Another place is the yahoo group jobshophomeshop.
> this is one place people post jobs to be done and
> others in the
> community do them. (for a fee)
>
> Dave
>
>
>
>
>
> >
> >
> > --- justinasia <justinasia@...> wrote:
> >
> > > Moderators note :
> > > Please respond OFF LIST if you want to discuss
> this
> > > project.
> > >
> > > But, if you have links to where he could go,
> that
> > > would be OK to post on-list.
> > >
> > > ==============================================
> > >
> > > Hi everyone,
> > >
> > > I need some tools made, and I do not know where
> to
> > > look. I am hoping
> > > that some of you may be able to point me to who
> I
> > > could get to make
> > > these tools.
> > >
> > > I need a set of gauges to measure pipe diameter.
> The
> > > method is to have
> > > round disks attached to the end of a rod, and
> then I
> > > insert that into
> > > a tapered pipe, so I can measure when it stops.
> The
> > > rod is attached to
> > > the flat side of the disk, so the disk is like a
> > > cross section of the pipe.
> > >
> > > So, these disks are made with a lathe. I need a
> set
> > > of them.
> > > -Thickness = 3mm. accuracy not so important.
> About
> > > 3mm.
> > > -Diameter from 10mm to 30mm, in 0.1mm increments
> (ie
> > > 10.0, 10.1, 10.2,
> > > 10.3 etc). Tolerance should be plus or minus
> 0.01mm
> > > -Each disk has a hole through the middle,
> threaded
> > > so it can attach to
> > > a rod. Needs to be straight.
> > > -Material = stainless steel.
> > >
> > > If anyone would have an idea to how much this
> would
> > > cost, how long it
> > > would take to make and where I can get it done,
> I
> > > would be very grateful.
> > >
> > > Thank you
> > >
> > > Justin
> > >
> > > -> REMEMBER - job related responses - OFF-LIST
> <-
> > >
> > >
> > >
> > >
> > >
> >
> >
> >
> >
> >
>
> > Sponsored Link____________________________________________________________________________________
> >
> > $420k for $1,399/mo.
> > Think You Pay Too Much For Your Mortgage?
> > Find Out! www.LowerMyBills.com/lre
> >
>
>
>
>
Do you Yahoo!?
Everyone is raving about the all-new Yahoo! Mail beta.
http://new.mail.yahoo.com
Discussion Thread
justinasia
2006-11-17 07:52:07 UTC
Need to commission a job
pandya amit
2006-11-17 10:35:01 UTC
Re: [CAD_CAM_EDM_DRO] Need to commission a job
turbulatordude
2006-11-18 05:47:50 UTC
Re: Need to commission a job
Justin .
2006-11-18 14:43:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need to commission a job