CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Repeatability of microswitches

on 2000-07-21 18:36:45 UTC
Spehro,

Good question, I'm in the same place. The motors run, now it's time to
add limit switches and a HOME. I'm thinking about using a photo
interrupter, and AND the signal with a phase from the stepper. This
narrows the "width" of the home. Now, where to put them?

Alan (sherline/sears Mill RETROFIT)


Spehro Pefhany wrote:
>
> Hi, all
>
> I'm working on a mill CNC conversion, among other things, and
> am wondering about the best way to do the 'home' switches.
>
> Are microswitches repeatable to a few thou or better, or would
> something else be better (photo interruptor, or hall effect ?).
>
> Thanks for any input,
>
> Best regards,
> =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
> Spehro Pefhany --"it's the network..." "The Journey is the reward"
> speff@... Info for manufacturers: http://www.trexon.com
> Embedded software/hardware/analog Info for designers: http://www.speff.com
> Contributions invited->The AVR-gcc FAQ is at: http://www.bluecollarlinux.com
> =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
>
> ------------------------------------------------------------------------
> Remember all those 80's songs about changing the world? Well, we're
> finally old enough to make those changes. Click to prove you meant it.
> http://click.egroups.com/1/6704/4/_/423600/_/964212566/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager

Discussion Thread

Jon Anderson 2000-07-21 14:15:25 UTC Re: [CAD_CAM_EDM_DRO] Repeatability of microswitches Darrell 2000-07-21 14:22:15 UTC Re: [CAD_CAM_EDM_DRO] Repeatability of microswitches Jon Elson 2000-07-21 16:23:59 UTC Re: [CAD_CAM_EDM_DRO] Repeatability of microswitches Alan Marconett KM6VV 2000-07-21 18:36:45 UTC Re: [CAD_CAM_EDM_DRO] Repeatability of microswitches Ian Wright 2000-07-22 06:05:49 UTC Re: [CAD_CAM_EDM_DRO] Repeatability of microswitches Alan Marconett KM6VV 2000-07-22 10:54:03 UTC Re: [CAD_CAM_EDM_DRO] Repeatability of microswitches Ian Wright 2000-07-22 13:31:39 UTC Re: [CAD_CAM_EDM_DRO] Repeatability of microswitches psp@p... 2000-07-24 05:37:55 UTC Re: [CAD_CAM_EDM_DRO] Repeatability of microswitches Alan Marconett KM6VV 2000-07-24 10:15:59 UTC Re: [CAD_CAM_EDM_DRO] Repeatability of microswitches