Re: [CAD_CAM_EDM_DRO] upgrade cnc
Posted by
Bob Campbell
on 2007-04-17 10:37:48 UTC
Bill,
Baldor makes a board that may help. I used one recently for a customer. Reversing the direction of a DC motor on the fly may be a problem. You basically need to stop the motor and reverse the wires.
Robert Colin Campbell
Bob Campbell Designs
www.Campbelldesigns.net
Mach 2/3 breakout boards
Relay boards
Spindle Speed boards
Stepper motors
Plasma Torch Height control
Baldor makes a board that may help. I used one recently for a customer. Reversing the direction of a DC motor on the fly may be a problem. You basically need to stop the motor and reverse the wires.
Robert Colin Campbell
Bob Campbell Designs
www.Campbelldesigns.net
Mach 2/3 breakout boards
Relay boards
Spindle Speed boards
Stepper motors
Plasma Torch Height control
----- Original Message -----
From: bill hribar
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Tuesday, April 17, 2007 11:12 AM
Subject: Re: [CAD_CAM_EDM_DRO] upgrade cnc
Hi Bob and all who are trying to help.
guess you can't read my mind and it would help to know what the motor is for. I want to use it to drive the spindle. In fact it is driving the spindle now with great success. I just wanted to use the PWM signal from mach3 to control the rpm and direction of the motor. that way i can do screw th'ds and the like.
thanks for the help.
Bill
Bob Campbell <bob@...> wrote:
Bill,
What are you going to use the 12 DC motor for?
Robert Colin Campbell
Bob Campbell Designs
www.Campbelldesigns.net
Mach 2/3 breakout boards
Relay boards
Spindle Speed boards
Stepper motors
Plasma Torch Height control
----- Original Message -----
From: billhribar
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Monday, April 16, 2007 2:08 PM
Subject: [CAD_CAM_EDM_DRO] upgrade cnc
Hi all:
I am upgrading a small cnc to a more powerful cnc and am using mach-3.
what I need to know is how to interface the PWM signal from mach-3 to
drive my 12 volt DC motor. You can't just connect the output of the
parallrl port to a mosfet driver, can you??? what kind of circuit do i
need? Anyone?
thanks:
Bill
[Non-text portions of this message have been removed]
---------------------------------
Ahhh...imagining that irresistible "new car" smell?
Check outnew cars at Yahoo! Autos.
---------------------------------
Ahhh...imagining that irresistible "new car" smell?
Check outnew cars at Yahoo! Autos.
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
Discussion Thread
billhribar
2007-04-16 12:08:27 UTC
upgrade cnc
Bob Campbell
2007-04-16 16:40:55 UTC
Re: [CAD_CAM_EDM_DRO] upgrade cnc
ballendo
2007-04-16 17:02:53 UTC
Re: upgrade cnc
bill hribar
2007-04-17 09:12:37 UTC
Re: [CAD_CAM_EDM_DRO] upgrade cnc
Bob Campbell
2007-04-17 10:37:48 UTC
Re: [CAD_CAM_EDM_DRO] upgrade cnc
Mark Vaughan
2007-04-17 13:02:43 UTC
RE: [CAD_CAM_EDM_DRO] upgrade cnc