Re: [CAD_CAM_EDM_DRO] Re: G320 Position Error Fault
Posted by
Dan Mauch
on 2007-07-04 13:22:33 UTC
One other thing you might try is to lower the acceleration rate.
Dan Mauch
economical 3D scanner software and kits
low cost stepper and servo motors.
cases for Gecko drives
kits and assembled 3-4 axis drives
www.camtronics-cnc.com
www.seanet.com/~dmauch
Dan Mauch
economical 3D scanner software and kits
low cost stepper and servo motors.
cases for Gecko drives
kits and assembled 3-4 axis drives
www.camtronics-cnc.com
www.seanet.com/~dmauch
----- Original Message -----
From: caudlet
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Wednesday, July 04, 2007 12:48 PM
Subject: [CAD_CAM_EDM_DRO] Re: G320 Position Error Fault
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "shadi_salhab_78" <salhab@...>
wrote:
>
> Hi all,
> I have been tunning my G320 servo drive for a big Fanuc motor every
> thing went perfect , I can jog smoothly accelerating and decelerating
> to full speed with out any Position Error Fault LED lights .
> The Problem arise when sudden stop happen ( when stopping a G00
> command by pressing ESC on the keyboard ) the Fault LED lights
>
> The 128-+ counts are too little to stop a big Inertia motor !
>
> The Damping Trimpot is at full scale , Gain and limit Trimpots 3/4 of
> full .
> I reduced the full speed (from Mach3)it helped solving the problem but
> not a very practical solution !
> What should I do ? Is there any way to increase the 128-+ counts
> error or eliminate it ?
>
> Thanks,
> Shadi Salhab
>
What line count encoder are you using? By dropping to a lower line
count you will fault at a greater following error. It will cost you
resolution but with gearing and leadscrews the steps per are probably
small increments anyway. There is no way to adjust the 128 count
number in the existing 320/340
[Non-text portions of this message have been removed]
Discussion Thread
shadi_salhab_78
2007-07-04 12:09:39 UTC
G320 Position Error Fault
caudlet
2007-07-04 12:51:30 UTC
Re: G320 Position Error Fault
Dan Mauch
2007-07-04 13:22:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: G320 Position Error Fault
shadi_salhab_78
2007-07-04 21:53:23 UTC
Re: G320 Position Error Fault
R Rogers
2007-07-04 22:14:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: G320 Position Error Fault
fortino tan
2007-07-05 05:26:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: G320 Position Error Fault
Jon Elson
2007-07-05 08:34:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: G320 Position Error Fault
R Rogers
2007-07-05 08:50:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: G320 Position Error Fault
Stephen Wille Padnos
2007-07-05 09:10:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: G320 Position Error Fault
Jon Elson
2007-07-05 17:50:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: G320 Position Error Fault