Re: [CAD_CAM_EDM_DRO] Spindle motors
Posted by
David G. LeVine
on 2007-08-28 19:43:33 UTC
At 10:22 PM 8/28/2007, you wrote:
They tend to run from 10 Volts to 40 Volts. And I was wrong,
controllers now go to 300 Amps!
Still, a 1 HP, 60K RPM engraving spindle is reasonably hefty. For
slower speeds, more conventional motors and VFDs are probably a better choice.
Since the motors are optimized for props and ducted fans, I bet a
smaller ducted fan would both cool the motor and remove the engraving chips...
David G. LeVine
Nashua, NH 03060
>By the way, what is the voltage rating on those motors? I didn't seeCount the NiCad cells and multiply by 1.25 or the LiPo cells and multiply by 4.
>one listed.
They tend to run from 10 Volts to 40 Volts. And I was wrong,
controllers now go to 300 Amps!
Still, a 1 HP, 60K RPM engraving spindle is reasonably hefty. For
slower speeds, more conventional motors and VFDs are probably a better choice.
Since the motors are optimized for props and ducted fans, I bet a
smaller ducted fan would both cool the motor and remove the engraving chips...
David G. LeVine
Nashua, NH 03060
Discussion Thread
ccosentino2001
2007-08-28 16:58:57 UTC
siemens program repeat
David G. LeVine
2007-08-28 19:11:26 UTC
Spindle motors
Michael Fagan
2007-08-28 19:32:30 UTC
Re: [CAD_CAM_EDM_DRO] Spindle motors
David G. LeVine
2007-08-28 19:43:33 UTC
Re: [CAD_CAM_EDM_DRO] Spindle motors
caudlet
2007-08-29 06:00:13 UTC
Re: Spindle motors
R Rogers
2007-08-29 07:28:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Spindle motors
Stephen Wille Padnos
2007-08-29 07:42:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Spindle motors
David G. LeVine
2007-08-29 07:55:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Spindle motors
Hugh Prescott
2007-08-29 09:11:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Spindle motors
Jon Elson
2007-08-29 09:42:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Spindle motors
William Perun Sr
2007-08-29 18:08:57 UTC
Re: Spindle motors
Michael Fagan
2007-08-29 18:16:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Spindle motors
David G. LeVine
2007-08-29 19:33:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Spindle motors
David G. LeVine
2007-08-29 19:34:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Spindle motors
Graham Stabler
2007-08-30 00:55:45 UTC
Re: Spindle motors
Hugh Prescott
2007-08-30 07:45:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Spindle motors