CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] stepper driver help

Posted by Yahoo
on 2007-09-27 11:49:42 UTC
LMD18245 (that's a single 3-amp H-Bridge, you would need two.) If you're
looking for a ready-made driver, I have some based on the LMD18245.
--
Phil Mattison
http://www.ohmikron.com/
Motors::Drivers::Controllers::Software

----- Original Message -----
From: stefan_sharpe <stefan_sharpe@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, September 26, 2007 6:07 PM
Subject: [CAD_CAM_EDM_DRO] stepper driver help


> My conversion project is going pretty slow right now- I am searching
> around on the net reading everything I can, to learn about what I am
> doing. Educated types might even call what I am doing reasearch...
> not sure if it is though as it is pretty fun so far :>
>
> Anyway, I had a lot of really good advice when I first posted- I
> hope I did not offend any of you with repeditive questions!
>
> I have also been hunting high and low for a bipolar stepper driver
> circuit that will go more than 2A, but they seem to be rare devils!
>
> I have found two 2A bipolar drivers and I keep wondering what the
> restrictions will be if i use them with Nema23 size motors. I know
> this is a difficult question to answer, but can anyone give me a bit
> of insight here?
>
> Thanks,
> Stefan
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>

Discussion Thread

stefan_sharpe 2007-09-26 18:07:34 UTC stepper driver help Michael Fagan 2007-09-26 18:26:50 UTC Re: [CAD_CAM_EDM_DRO] stepper driver help David G. LeVine 2007-09-26 21:29:54 UTC Re: [CAD_CAM_EDM_DRO] stepper driver help hannu 2007-09-27 01:36:55 UTC Re: [CAD_CAM_EDM_DRO] stepper driver help Paul Kelly 2007-09-27 03:43:13 UTC RE: [CAD_CAM_EDM_DRO] stepper driver help stefan_sharpe 2007-09-27 07:00:12 UTC Re: stepper driver help Michael Fagan 2007-09-27 07:05:39 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper driver help Paul Kelly 2007-09-27 07:07:32 UTC RE: [CAD_CAM_EDM_DRO] Re: stepper driver help turbulatordude 2007-09-27 07:13:18 UTC Re: stepper driver help John Dammeyer 2007-09-27 07:51:20 UTC RE: [CAD_CAM_EDM_DRO] stepper driver help Alan KM6VV 2007-09-27 10:01:15 UTC RE: [CAD_CAM_EDM_DRO] stepper driver help Yahoo 2007-09-27 11:49:42 UTC Re: [CAD_CAM_EDM_DRO] stepper driver help Wayne C. Gramlich 2007-09-27 14:05:29 UTC Re: stepper driver help John Dammeyer 2007-09-27 14:34:13 UTC RE: [CAD_CAM_EDM_DRO] Re: stepper driver help Steve Blackmore 2007-09-27 14:47:53 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper driver help Wayne C. Gramlich 2007-09-27 14:55:19 UTC Re: stepper driver help Sebastian Kuzminsky 2007-09-27 15:30:56 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper driver help Steve Blackmore 2007-09-27 15:39:20 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper driver help Paul Kelly 2007-09-27 15:44:45 UTC RE: [CAD_CAM_EDM_DRO] Re: stepper driver help Wayne C. Gramlich 2007-09-27 15:49:41 UTC Re: stepper driver help John Dammeyer 2007-09-27 16:30:52 UTC RE: [CAD_CAM_EDM_DRO] Re: stepper driver help Stephen Wille Padnos 2007-09-27 16:55:18 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper driver help John Dammeyer 2007-09-27 17:41:42 UTC RE: [CAD_CAM_EDM_DRO] Re: stepper driver help Yahoo 2007-09-27 18:06:51 UTC Re: stepper driver help David G. LeVine 2007-09-27 19:41:52 UTC RE: [CAD_CAM_EDM_DRO] Re: stepper driver help John Dammeyer 2007-09-27 20:26:20 UTC RE: [CAD_CAM_EDM_DRO] Re: stepper driver help tech@c... 2007-09-27 20:50:00 UTC RE: [CAD_CAM_EDM_DRO] Re: stepper driver help Sebastian Kuzminsky 2007-09-27 21:05:29 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper driver help Sebastian Kuzminsky 2007-09-27 21:41:19 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper driver help Stephen Wille Padnos 2007-09-27 21:55:55 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper driver help Sebastian Kuzminsky 2007-09-27 22:24:11 UTC Re: [CAD_CAM_EDM_DRO] Re: stepper driver help turbulatordude 2007-09-28 05:23:58 UTC Re: stepper driver help