CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM

on 2008-03-10 13:51:05 UTC
Thanks Paul,

the rep was very pushy and didn't explain that, guess i need to ask a few questions before i leap

Nev


----- Original Message ----
From: Don Erickson <erickson@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Monday, 10 March, 2008 5:08:06 PM
Subject: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM

V22 is a more intuitive software than V21. Unfortunately, whereas V21
did 2D and 3D, they have split V22 into packages. The basic version
does 2D -- pocketing, profiling and engraving. There is another
package that allows 3D and still another (V22 Pro) that includes
Z-level functions that enhance 3D work. So, the version you were
offered was the basic version.
best,
Paul

--- In CAD_CAM_EDM_ DRO@yahoogroups. com, NEVILLE WEBSTER
<nevillewebster@ ...> wrote:
>
> hi Jack,
>
> just come off the phone with a Bobcad rep offering same deal, but
don't know enough about the software to make a decision. If any users
are on line would be good to get some feedback as to Bobcad as i last
looked at ver 18 and wasn't to impressed.




[Non-text portions of this message have been removed]

Discussion Thread

Bob Durst 2005-12-28 15:53:02 UTC BobCAD/CAM Jack Mc Kie 2008-03-10 09:37:26 UTC BobCAD/CAM NEVILLE WEBSTER 2008-03-10 09:41:08 UTC Re: [CAD_CAM_EDM_DRO] BobCAD/CAM Don Erickson 2008-03-10 13:47:35 UTC Re: BobCAD/CAM NEVILLE WEBSTER 2008-03-10 13:51:05 UTC Re: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM shawn c 2008-03-10 14:51:33 UTC RE: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM Don Erickson 2008-03-10 17:15:43 UTC Re: BobCAD/CAM shawn c 2008-03-10 17:48:48 UTC RE: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM Ron Kline 2008-03-10 18:09:24 UTC Re: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM Don Erickson 2008-03-10 21:07:10 UTC Re: BobCAD/CAM Don Erickson 2008-03-10 21:07:13 UTC Re: BobCAD/CAM Hodges Guitars 2008-03-10 21:09:30 UTC Re: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM Jack McKie 2008-03-10 21:09:30 UTC RE: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM paultitchener 2008-03-11 09:01:24 UTC Re: BobCAD/CAM Jack McKie 2008-03-11 15:26:26 UTC Re: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM Harko Schwartz 2008-03-11 22:06:58 UTC Re: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM William C. Griggs 2008-03-12 05:34:53 UTC Re: BobCAD/CAM Polaraligned 2008-03-13 03:24:08 UTC Re: BobCAD/CAM dgoadby 2008-03-16 04:02:18 UTC Re: BobCAD/CAM Scot Rogers 2008-03-16 11:40:09 UTC [CAD_CAM_EDM_DRO] Looking for an old bar feed shawn c 2008-03-16 12:44:27 UTC RE: [CAD_CAM_EDM_DRO] Re: BobCAD/CAM pml58@s... 2008-03-17 13:16:28 UTC Re: [CAD_CAM_EDM_DRO] Looking for an old bar feed