RE: [CAD_CAM_EDM_DRO] Servo motor questions
Posted by
Dan Mauch
on 2010-06-12 07:02:23 UTC
The motor torque will remain the same. The speed however, will be
proportional to the voltage in this case 50%.
www.camtronics-cnc.com
dmauch@...
Low prices on Gecko drive, cases , sepper and servo motors.
3d scanner
From: CAD_CAM_EDM_DRO@yahoogroups.com
[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of cnc_4_me
Sent: Friday, June 11, 2010 3:43 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Servo motor questions
If you have a servo motor rated at 160 volts, 10 amps, 5nM, and you are
driving it with a Gecko 80 volt 20 amp drive. What happens to the 5nM torque
rating. Since the voltage you are driving it with is so low, can you make
the 10 amps required for 5nM of torque.
Also, how is the belt usually tensioned for a Nema 34 or 42 motor. Are the 4
motor bolt holes slotted. Or is an idler used.
cnc4me
[Non-text portions of this message have been removed]
proportional to the voltage in this case 50%.
www.camtronics-cnc.com
dmauch@...
Low prices on Gecko drive, cases , sepper and servo motors.
3d scanner
From: CAD_CAM_EDM_DRO@yahoogroups.com
[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of cnc_4_me
Sent: Friday, June 11, 2010 3:43 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Servo motor questions
If you have a servo motor rated at 160 volts, 10 amps, 5nM, and you are
driving it with a Gecko 80 volt 20 amp drive. What happens to the 5nM torque
rating. Since the voltage you are driving it with is so low, can you make
the 10 amps required for 5nM of torque.
Also, how is the belt usually tensioned for a Nema 34 or 42 motor. Are the 4
motor bolt holes slotted. Or is an idler used.
cnc4me
[Non-text portions of this message have been removed]
Discussion Thread
cnc_4_me
2010-06-11 15:45:00 UTC
Servo motor questions
Stephen Wille Padnos
2010-06-11 17:29:02 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor questions
Michael Fagan
2010-06-11 18:11:55 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor questions
cnc_4_me
2010-06-11 19:16:16 UTC
Re: Servo motor questions
Jon Elson
2010-06-11 21:52:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo motor questions
Randall Wink
2010-06-12 04:33:18 UTC
RE: [CAD_CAM_EDM_DRO] Re: Servo motor questions
Dan Mauch
2010-06-12 07:02:23 UTC
RE: [CAD_CAM_EDM_DRO] Servo motor questions
cnc_4_me
2010-06-12 15:10:43 UTC
Re: Servo motor questions
Randall Wink
2010-06-12 16:09:58 UTC
RE: [CAD_CAM_EDM_DRO] Re: Servo motor questions
Nathan Clark
2010-06-12 23:49:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo motor questions
Steve Blackmore
2010-06-13 01:38:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo motor questions