CAD CAM EDM DRO - Yahoo Group Archive

Re: Gecko 203V disable light with Smoothstepper

Posted by jimmy_staton
on 2011-09-23 13:13:46 UTC
Thanks that's what I suspected. I'll add the resistors and let you know.

--- In CAD_CAM_EDM_DRO@yahoogroups.com, "bob campbell" <bob@...> wrote:
>
> Jimmy,
>
> The problem that I had and one of my customers also had was the disable led
> started blinking and then went on solid during a cut. On my control box I
> was running 7 amps motors. I did not have a current set resistor installed.
> I installed a current set resistor for about 6.5 amps. This fixed my
> problem. For my customer I recommended that he check the current set
> resistor and decrease the current by about 10%. This fixed his problem.
>
> You are not the only one that has had the same problem.
>
> Bob Campbell
>
> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of jimmy_staton
> Sent: Friday, September 23, 2011 11:51 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Gecko 203V disable light with Smoothstepper
>
> I'm running a SmoothStepper with 3 X 203V Gecko's all is fine testing the
> drives
> at about 30 Inches a min but If I get much above that the 203V for that axis
> set the Red disable light and I have to recycle the power connected to the
> 203V's to reset it.
> It also did the same thing running for a parallel port so I don't thing it's
> the controller.
>
> I have shield cable connected to the Step, Dir, Ena and GND I am run at
> 20,000 steps
> per inch on ball screw, am I just trying to get too high a inch Per/ min
> from these drivers?
>
>
>
> ------------------------------------
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
> you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for OT
> subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
> Yahoo! Groups Links
>

Discussion Thread

jimmy_staton 2011-09-23 09:51:18 UTC Gecko 203V disable light with Smoothstepper bob campbell 2011-09-23 11:41:11 UTC RE: [CAD_CAM_EDM_DRO] Gecko 203V disable light with Smoothstepper jimmy_staton 2011-09-23 13:13:46 UTC Re: Gecko 203V disable light with Smoothstepper jimmy_staton 2011-10-01 09:05:26 UTC Re: Gecko 203V disable light with Smoothstepper