CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Updated DRO using screw threads not pulleys

Posted by Darrell
on 2000-08-18 22:41:47 UTC
It was an HP plotter with about 18" by 18" travel and accuracy and
repeatability were excellent.
Darrell

----- Original Message -----
From: <JanRwl@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Friday, August 18, 2000 8:44 PM
Subject: Re: [CAD_CAM_EDM_DRO] Updated DRO using screw threads not pulleys


> In a message dated 8/17/00 11:42:36 PM Central Daylight Time,
> dgehlsen@... writes:
>
> << An old plotter that I had used a drum and coated wire to move the pens.
the
> wire was fixed at the center of the drum and when the pen was at one
limit,
> one half of the drum was full and the other half was almost empty. That
way
> the wire always traveled in the same place on the drum.
> Darrell >>
>
> Darrell: Was that a Varian brand? I had an old Varian with that
mechanism,
> and it worked fine, but I don't think I'd advocate it for "CNC"! For
> plotting on PAPER, it was fine. For DRO? I don't think the
"repeatability"
> would be worth a dang.
>
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>

Discussion Thread

Doug Fortune 2000-08-17 18:20:36 UTC Re: [CAD_CAM_EDM_DRO] Updated DRO using screw threads not pulleys dave engvall 2000-08-17 18:59:21 UTC Re: [CAD_CAM_EDM_DRO] Updated DRO using screw threads not pulleys Darrell 2000-08-17 21:41:33 UTC Re: [CAD_CAM_EDM_DRO] Updated DRO using screw threads not pulleys Ian Wright 2000-08-18 05:23:29 UTC Re: [CAD_CAM_EDM_DRO] Updated DRO using screw threads not pulleys MRC 2000-08-18 06:44:38 UTC Re: [CAD_CAM_EDM_DRO] Updated DRO using screw threads not pulleys ptengin@a... 2000-08-18 11:49:40 UTC Re: [CAD_CAM_EDM_DRO] Updated DRO using screw threads not pulleys JanRwl@A... 2000-08-18 20:44:39 UTC Re: [CAD_CAM_EDM_DRO] Updated DRO using screw threads not pulleys Darrell 2000-08-18 22:41:47 UTC Re: [CAD_CAM_EDM_DRO] Updated DRO using screw threads not pulleys