Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Posted by
ptengin@a...
on 2000-08-21 17:18:36 UTC
In a message dated 08/21/2000 1:17:08 PM Hawaiian Standard Time,
jmelson@... writes:
<< Ah, HA! Now, you are getting somewhere. Clearly, it is some sort of
interference
problem, radiation from the motor wires and other things are
contaminating
the step and/or direction inputs to the driver. >>
I had similar problems on mine. I installed decoupling caps and went to
twisted pairs of 20 or 22 ga wire for the signal, no shield. The problem went
away!! I don't recall the value of the decoupling caps but they must be small
as larger caps did manage to dampen the pulse when observed on a scope.
Perhaps Jon would have the value off the top of his head. I'd have to drive
out to my dad's place to look/see. Good luck
Peter
THRD, Inc.
jmelson@... writes:
<< Ah, HA! Now, you are getting somewhere. Clearly, it is some sort of
interference
problem, radiation from the motor wires and other things are
contaminating
the step and/or direction inputs to the driver. >>
I had similar problems on mine. I installed decoupling caps and went to
twisted pairs of 20 or 22 ga wire for the signal, no shield. The problem went
away!! I don't recall the value of the decoupling caps but they must be small
as larger caps did manage to dampen the pulse when observed on a scope.
Perhaps Jon would have the value off the top of his head. I'd have to drive
out to my dad's place to look/see. Good luck
Peter
THRD, Inc.
Discussion Thread
Tim Goldstein
2000-08-14 10:55:55 UTC
RE: [CAD_CAM_EDM_DRO] Re: Lost steps
Joe Vicars
2000-08-15 14:33:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Ozzie@h...
2000-08-20 13:41:24 UTC
Re: Lost steps
Mariss Freimanis
2000-08-20 15:57:28 UTC
Re: Lost steps
JanRwl@A...
2000-08-20 17:10:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Ozzie@h...
2000-08-20 20:04:20 UTC
Re: Lost steps
Ozzie@h...
2000-08-20 20:23:39 UTC
Re: Lost steps
Mariss Freimanis
2000-08-20 23:57:26 UTC
Re: Lost steps
Jon Elson
2000-08-21 16:08:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
ptengin@a...
2000-08-21 17:18:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Ozzie@h...
2000-08-21 20:02:49 UTC
Re: Lost steps
dave engvall
2000-08-21 20:24:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
JanRwl@A...
2000-08-21 21:04:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Ozzie@h...
2000-08-21 21:47:02 UTC
Re: Lost steps
Ozzie@h...
2000-08-21 22:00:05 UTC
Re: Lost steps
Jon Elson
2000-08-21 23:22:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
ptengin@a...
2000-08-21 23:47:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Jon Elson
2000-08-22 13:31:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
ptengin@a...
2000-08-22 15:44:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Mariss Freimanis
2000-08-22 17:17:03 UTC
Re: Lost steps
wanliker@a...
2000-08-22 17:42:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Mariss Freimanis
2000-08-22 18:37:23 UTC
Re: Lost steps
JanRwl@A...
2000-08-22 21:36:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Jon Elson
2000-08-22 22:16:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Ian Wright
2000-08-23 04:19:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Ozzie@h...
2000-08-23 11:49:05 UTC
Re: Lost steps
Tim Goldstein
2000-08-23 13:19:04 UTC
RE: [CAD_CAM_EDM_DRO] Re: Lost steps
hans
2000-08-23 13:49:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
JanRwl@A...
2000-08-23 15:04:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps
Ian Wright
2000-08-24 01:08:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lost steps