CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay

Posted by Darrell
on 2000-09-04 18:37:26 UTC
----- Original Message -----
From: "mgrady" <mgrady@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Sunday, September 03, 2000 9:19 PM
Subject: Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay


>
> how slow is slow on the knee
> and how did the Spindle wizard work
> mike
>
I have heard about 30/35 IPM. The spindle Wizard is an air over hydraulic
mechanism that runs the spindle up and down. there is also a turret with
different length adjustable posts on it that set how far down the spindle
goes. Our control interfaces with both and most use it for tool changes.
Darrell


> Darrell wrote:
>
> > . With Z
> > on the knee as they are, they have a lot of travel but not a lot of
speed on
> > the knee. Be sure that you lock the knee clamps before you turn off the
> > power.
> > Darrell AL7DO
> > http://www.machinemaster.com
> >
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>

Discussion Thread

Carey L. Culpepper 2000-09-03 19:02:45 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay ptengin@a... 2000-09-03 19:28:37 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay mgrady 2000-09-03 20:11:56 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Tim Goldstein 2000-09-03 20:21:23 UTC RE: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay dave engvall 2000-09-03 20:37:34 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay mgrady 2000-09-03 20:38:34 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Darrell 2000-09-03 21:07:17 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay mgrady 2000-09-03 21:19:10 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Jon Anderson 2000-09-03 22:59:22 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Jon Anderson 2000-09-03 23:04:50 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Jon Elson 2000-09-04 00:06:59 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Jon Elson 2000-09-04 00:12:08 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Jon Elson 2000-09-04 00:16:07 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay ptengin@a... 2000-09-04 01:51:23 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Ian Wright 2000-09-04 11:52:01 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Darrell 2000-09-04 18:37:26 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Darrell 2000-09-04 18:44:18 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay Jon Elson 2000-09-04 22:42:03 UTC Re: [CAD_CAM_EDM_DRO] Heads up, CNC mill going cheap on ebay