RE: [CAD_CAM_EDM_DRO] Re: 50uF + suplus motor run caps sources???

Thanks Ken!!

At 10:06 PM 9/27/00 -0700, you wrote:

>Well, I know I can get 60 uF for the pump motors I install. Let me find out
>what the cost is on them and I'll email you for 8 of them or so?
>
>KT
>
>
>-----Original Message-----
>From: Lee Studley [mailto:indigo_red@...]
>Sent: Wednesday, September 27, 2000 9:32 PM
>To: CAD_CAM_EDM_DRO@egroups.com
>Subject: [CAD_CAM_EDM_DRO] Re: 50uF + suplus motor run caps sources???
>
>
>Best deal they have is 50uF @ 370VAC for $19.90 (#5X433)
>was hoping for a little cheaaper, but may do.
>
>-Lee
>
>
>
>
>--- In CAD_CAM_EDM_DRO@egroups.com, "Ken Thompson" <ken@t...> wrote:
>> Go back to Graingers?
>>
>> KT
>>
>>
>> -----Original Message-----
>> From: Lee Studley [mailto:indigo_red@u...]
>> Sent: Wednesday, September 27, 2000 8:39 PM
>> To: CAD_CAM_EDM_DRO@egroups.com
>> Subject: [CAD_CAM_EDM_DRO] 50uF + suplus motor run caps sources???
>>
>>
>> Hello all,
>>
>> I'm making a rotary convertor (7.5hp idler or 10hp idler)
>> and I need some big motor-run caps for a total
>> approx of 100uF-500uF .?.
>>
>> Does anyone know of an affordable source?
>>
>> I have 20 6uF run caps, but they are only 236vac rated. Is
>> this cutting it too close? Takes up alot of space too. Luckily they
>> only cost me $19 total. Anyone need some if they dont work out?
>>
>> I'm using the design that has a potential relay for starting.
>> Already got that from Grainger.
>>
>> Thanks in advance for any input.
>>
>>
>>
>>
>> Welcome to CAD_CAM_EDM_DRO@e...,an unmoderated list for the
>> discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>>
>> Addresses:
>> Post message: CAD_CAM_EDM_DRO@egroups.com
>> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
>> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
>> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@a...
>> Moderator: jmelson@a... [Moderator]
>> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
>> FAQ: http://www.ktmarketing.com/faq.html
>> bill,
>> List Manager
>
>
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@egroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
>List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
>Moderator: jmelson@... [Moderator]
>URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
>FAQ: http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the

discussion of shop built systems, for CAD, CAM, EDM, and DRO.

>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@egroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
>List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
>Moderator: jmelson@... [Moderator]
>URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
>FAQ: http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>
>