RE: [CAD_CAM_EDM_DRO] Re: 50uF + suplus motor run caps sources???

Well, I know I can get 60 uF for the pump motors I install. Let me find out
what the cost is on them and I'll email you for 8 of them or so?

KT


-----Original Message-----
From: Lee Studley [mailto:indigo_red@...]
Sent: Wednesday, September 27, 2000 9:32 PM
To: CAD_CAM_EDM_DRO@egroups.com
Subject: [CAD_CAM_EDM_DRO] Re: 50uF + suplus motor run caps sources???


Best deal they have is 50uF @ 370VAC for $19.90 (#5X433)
was hoping for a little cheaaper, but may do.

-Lee

--- In CAD_CAM_EDM_DRO@egroups.com, "Ken Thompson" <ken@t...> wrote:
> Go back to Graingers?
>
> KT
>
>
> -----Original Message-----
> From: Lee Studley [mailto:indigo_red@u...]
> Sent: Wednesday, September 27, 2000 8:39 PM
> To: CAD_CAM_EDM_DRO@egroups.com
> Subject: [CAD_CAM_EDM_DRO] 50uF + suplus motor run caps sources???
>
>
> Hello all,
>
> I'm making a rotary convertor (7.5hp idler or 10hp idler)
> and I need some big motor-run caps for a total
> approx of 100uF-500uF .?.
>
> Does anyone know of an affordable source?
>
> I have 20 6uF run caps, but they are only 236vac rated. Is
> this cutting it too close? Takes up alot of space too. Luckily they
> only cost me $19 total. Anyone need some if they dont work out?
>
> I'm using the design that has a potential relay for starting.
> Already got that from Grainger.
>
> Thanks in advance for any input.
>
>
>
>
> Welcome to CAD_CAM_EDM_DRO@e...,an unmoderated list for the
> discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@a...
> Moderator: jmelson@a... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager



Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.

Addresses:
Post message: CAD_CAM_EDM_DRO@egroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
Moderator: jmelson@... [Moderator]
URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
FAQ: http://www.ktmarketing.com/faq.html
bill,
List Manager