CAD CAM EDM DRO - Yahoo Group Archive

Re: Locating already drilled holes

on 2000-10-11 15:59:56 UTC
OK,

I saw one last night in a catalog, so what's a drill bushing? and what's
it used for? Goes in the jig under where the hole is supposed to go?

Alan

Anne Ogborn wrote:
>
> Alison & Jim Gregg wrote:
> >
> > Hi Annie
> >
> > Yes been there done that, but put the hole in the fixture that held the
> > parts - fixture already held parallel in x axis by Tee slot key, and set
> > machine zero.
> >
> > A stupid operation where a small number of parts had to be made each
> > Tuesday, and the machine then cleared.
> >
> > Jim Gregg.
> >
>
> LOL -
>
> I have to confess I once used something far worse.
>
> I was briefly employed in a machine shop as an assistant.
>
> I was in the midst of making 1 in a limited series of 80 bizillion
> holes in plates for something. We'd made a jig to hold the part, but
> didn't have a drill bushing.
>
> We didn't have a depth stop on it either. I was just pulling down until
> the drill came out the bottom of the part. On part about 289, I spaced out,
> pulled the handle too far, and, yep, drilled a hole in the table.
>
> At about part 814 the owner came along and needed to use the
> mill. He cranked the table down towards one end, changed tools, cut a slot,
> and left the machie sitting. I came back and realized I had no idea where
> to move the table back to. Fortunately I had my little accident.
> I put my drill back in the spindle, cranked the table back over the hole,
> and tweaked the handwheels until the drill centered in the
> hole. Locked the slides and continued production.
>
> Hope George isn't on this list, or if he is, he forgives me for drilling that hole.
>
> Annie
>

Discussion Thread

ballendo@y... 2000-10-09 19:35:49 UTC Locating already drilled holes Ian Wright 2000-10-10 02:30:18 UTC Re: [CAD_CAM_EDM_DRO] Locating already drilled holes Alan Marconett KM6VV 2000-10-10 12:05:58 UTC Re: [CAD_CAM_EDM_DRO] Locating already drilled holes Terry Ackland 2000-10-10 15:32:11 UTC Re: Locating already drilled holes cnc4me@u... 2000-10-10 17:27:26 UTC Re: Locating already drilled holes dave engvall 2000-10-10 18:05:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes ballendo@y... 2000-10-10 18:35:29 UTC Re: Locating already drilled holes ballendo@y... 2000-10-10 19:02:48 UTC Re: Re: Locating already drilled holes Anne Ogborn 2000-10-10 19:17:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes ballendo@y... 2000-10-10 19:34:24 UTC Re: Re: Locating already drilled holes Jon Anderson 2000-10-10 19:50:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes Alison & Jim Gregg 2000-10-10 19:58:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes dave engvall 2000-10-10 20:05:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Locating already drilled holes Ian Wright 2000-10-11 03:23:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes ptengin@a... 2000-10-11 03:39:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes James Owens 2000-10-11 08:59:19 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes Jon Elson 2000-10-11 12:27:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes Anne Ogborn 2000-10-11 13:30:14 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes Hugh Currin 2000-10-11 14:04:29 UTC Re: Locating already drilled holes Joe Vicars 2000-10-11 14:17:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes Tim Goldstein 2000-10-11 14:20:20 UTC RE: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes wanliker@a... 2000-10-11 15:29:54 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes Jerry Kimberlin 2000-10-11 15:30:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes Jon Elson 2000-10-11 15:30:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes paul@a... 2000-10-11 15:36:54 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes Alan Marconett KM6VV 2000-10-11 15:59:56 UTC Re: Locating already drilled holes Jerry Kimberlin 2000-10-11 16:12:14 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes Terry Ackland 2000-10-11 17:48:19 UTC Re: Locating already drilled holes Anne Ogborn 2000-10-11 22:28:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes ballendo@y... 2000-10-11 22:59:25 UTC Re: Re: Locating already drilled holes Ron Ginger 2000-10-12 06:27:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Locating already drilled holes Peter Chen 2000-10-13 15:33:00 UTC Re: Locating already drilled holes Alan Marconett KM6VV 2000-10-13 19:33:55 UTC Re: Locating already drilled holes