Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen
Posted by
Doug Harrison
on 2000-12-07 13:55:36 UTC
----- Original Message -----
From: Jon Elson <jmelson@...>
SNIP>In this case, the resolution of the
> pulse timing is what is critical, not necessarily the amount of CPU
> resources it takes to do that part. I can easily see an interrupt-driven,
> "pulse or no pulse this tick" type of routine that would NOT take much
> CPU resources, but would give very poor step pulse timing.
>
--- And that is what makes a difference between programs like CNCPro and
several other software-based profilers. The bump and grind associated with
interrupt driven pulse timing is what makes motors skip steps.
Doug
Discussion Thread
Alan Marconett KM6VV
2000-12-05 16:58:48 UTC
Pulse Gen
Wally K
2000-12-05 20:43:19 UTC
Re: Pulse Gen
Alan Marconett KM6VV
2000-12-05 21:56:36 UTC
Re: Pulse Gen
Wally K
2000-12-05 23:30:20 UTC
Re: Pulse Gen
Mariss Freimanis
2000-12-06 07:16:05 UTC
Re: Pulse Gen
Mariss Freimanis
2000-12-06 07:55:06 UTC
Re: Pulse Gen
Alan Marconett KM6VV
2000-12-06 11:42:09 UTC
Re: Pulse Gen
Wally K
2000-12-06 13:35:49 UTC
Re: Pulse Gen
Dan Mauch
2000-12-07 06:46:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen
Jon Elson
2000-12-07 12:00:37 UTC
Re: Pulse Gen
Jon Elson
2000-12-07 12:28:46 UTC
Re: Pulse Gen
Jon Elson
2000-12-07 12:35:32 UTC
Re: Pulse Gen
Jon Elson
2000-12-07 12:39:29 UTC
Re: Pulse Gen
Jeff Barlow
2000-12-07 12:46:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen
Doug Harrison
2000-12-07 13:55:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen
Mariss Freimanis
2000-12-07 15:17:36 UTC
Re: Pulse Gen
Jeff Barlow
2000-12-07 15:52:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen
Jon Elson
2000-12-07 15:54:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen
Jeff Barlow
2000-12-07 16:19:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen
Mariss Freimanis
2000-12-07 16:22:45 UTC
Re: Pulse Gen
Smoke
2000-12-07 16:32:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen
Jeff Barlow
2000-12-07 16:40:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen
Alan Marconett KM6VV
2000-12-07 20:41:50 UTC
Pulse Gen
Jeff Barlow
2000-12-07 20:57:34 UTC
Re: [CAD_CAM_EDM_DRO] Pulse Gen
ballendo@y...
2000-12-09 13:19:31 UTC
Re: Pulse Gen
ballendo@y...
2000-12-09 13:28:03 UTC
Re: Pulse Gen
ballendo@y...
2000-12-09 14:46:59 UTC
Re: Re: Pulse Gen