CAD CAM EDM DRO - Yahoo Group Archive

Re: Pulse Gen

Posted by Wally K
on 2000-12-05 20:43:19 UTC
I have been looking for something like this for awhile. It seems
that this is not a hardware only solution, you need some software
routines to hook into the program. If you figure something out let
me know.


Wally K.



--- In CAD_CAM_EDM_DRO@egroups.com, Alan Marconett KM6VV <KM6VV@a...>
wrote:
> Hi Mariss Jon, and the list,
>
> I was looking at new posted files on CCED, and revisited your
(Mariss)
> pulse generator block diagram (PulseGen.Doc). Do I understand that
it
> is possible (and a proper way) to do coordinated moves between
multiple
> axis by setting up a "pulse generator" for the three required rates,
> generate (or count) the needed steps in the major axis (farthest
> travel), and all axis get there? Is that the intent of your
circuit,
> and do I understand that you have a circuit that you wouldn't mind
> posting for this? I saw a very old circuit that used 8253 timers to
> generate rates and count steps for 3 axis, and built one of my own
(wire
> wrap!) for a robot back in about '84, but didn't do much with it. I
> have also thought about using 3 Cy-545's to generate profiles for
up to
> 3 axis, although I'm not sure how accurate the rates can be
generated.
>
> I know Jon is also working on a board that can generate rates. I
would
> like to go one of these 3 (?) ways, after looking at the software-
only
> approach! Yeah, it can be done ;>o
>
> Sometime soon I'd like to get some hardware!
>
> Alan KM6VV

Discussion Thread

Alan Marconett KM6VV 2000-12-05 16:58:48 UTC Pulse Gen Wally K 2000-12-05 20:43:19 UTC Re: Pulse Gen Alan Marconett KM6VV 2000-12-05 21:56:36 UTC Re: Pulse Gen Wally K 2000-12-05 23:30:20 UTC Re: Pulse Gen Mariss Freimanis 2000-12-06 07:16:05 UTC Re: Pulse Gen Mariss Freimanis 2000-12-06 07:55:06 UTC Re: Pulse Gen Alan Marconett KM6VV 2000-12-06 11:42:09 UTC Re: Pulse Gen Wally K 2000-12-06 13:35:49 UTC Re: Pulse Gen Dan Mauch 2000-12-07 06:46:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Jon Elson 2000-12-07 12:00:37 UTC Re: Pulse Gen Jon Elson 2000-12-07 12:28:46 UTC Re: Pulse Gen Jon Elson 2000-12-07 12:35:32 UTC Re: Pulse Gen Jon Elson 2000-12-07 12:39:29 UTC Re: Pulse Gen Jeff Barlow 2000-12-07 12:46:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Doug Harrison 2000-12-07 13:55:36 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Mariss Freimanis 2000-12-07 15:17:36 UTC Re: Pulse Gen Jeff Barlow 2000-12-07 15:52:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Jon Elson 2000-12-07 15:54:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Jeff Barlow 2000-12-07 16:19:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Mariss Freimanis 2000-12-07 16:22:45 UTC Re: Pulse Gen Smoke 2000-12-07 16:32:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Jeff Barlow 2000-12-07 16:40:14 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Alan Marconett KM6VV 2000-12-07 20:41:50 UTC Pulse Gen Jeff Barlow 2000-12-07 20:57:34 UTC Re: [CAD_CAM_EDM_DRO] Pulse Gen ballendo@y... 2000-12-09 13:19:31 UTC Re: Pulse Gen ballendo@y... 2000-12-09 13:28:03 UTC Re: Pulse Gen ballendo@y... 2000-12-09 14:46:59 UTC Re: Re: Pulse Gen