CAD CAM EDM DRO - Yahoo Group Archive

Re: Pulse Gen

on 2000-12-05 21:56:36 UTC
Hi Wally,

Sure, that's just the stuff I do! The driver(s) that I would write
would be compiled into the 'C' code jog/controller program I'm working
on.

Alan KM6VV


Wally K wrote:
>
> I have been looking for something like this for awhile. It seems
> that this is not a hardware only solution, you need some software
> routines to hook into the program. If you figure something out let
> me know.
>
> Wally K.
>
> --- In CAD_CAM_EDM_DRO@egroups.com, Alan Marconett KM6VV <KM6VV@a...>
> wrote:
> > Hi Mariss Jon, and the list,
> >
> > I was looking at new posted files on CCED, and revisited your
> (Mariss)
> > pulse generator block diagram (PulseGen.Doc). Do I understand that
> it
> > is possible (and a proper way) to do coordinated moves between
> multiple
> > axis by setting up a "pulse generator" for the three required rates,
> > generate (or count) the needed steps in the major axis (farthest
> > travel), and all axis get there? Is that the intent of your
> circuit, <snip>

Discussion Thread

Alan Marconett KM6VV 2000-12-05 16:58:48 UTC Pulse Gen Wally K 2000-12-05 20:43:19 UTC Re: Pulse Gen Alan Marconett KM6VV 2000-12-05 21:56:36 UTC Re: Pulse Gen Wally K 2000-12-05 23:30:20 UTC Re: Pulse Gen Mariss Freimanis 2000-12-06 07:16:05 UTC Re: Pulse Gen Mariss Freimanis 2000-12-06 07:55:06 UTC Re: Pulse Gen Alan Marconett KM6VV 2000-12-06 11:42:09 UTC Re: Pulse Gen Wally K 2000-12-06 13:35:49 UTC Re: Pulse Gen Dan Mauch 2000-12-07 06:46:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Jon Elson 2000-12-07 12:00:37 UTC Re: Pulse Gen Jon Elson 2000-12-07 12:28:46 UTC Re: Pulse Gen Jon Elson 2000-12-07 12:35:32 UTC Re: Pulse Gen Jon Elson 2000-12-07 12:39:29 UTC Re: Pulse Gen Jeff Barlow 2000-12-07 12:46:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Doug Harrison 2000-12-07 13:55:36 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Mariss Freimanis 2000-12-07 15:17:36 UTC Re: Pulse Gen Jeff Barlow 2000-12-07 15:52:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Jon Elson 2000-12-07 15:54:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Jeff Barlow 2000-12-07 16:19:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Mariss Freimanis 2000-12-07 16:22:45 UTC Re: Pulse Gen Smoke 2000-12-07 16:32:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Jeff Barlow 2000-12-07 16:40:14 UTC Re: [CAD_CAM_EDM_DRO] Re: Pulse Gen Alan Marconett KM6VV 2000-12-07 20:41:50 UTC Pulse Gen Jeff Barlow 2000-12-07 20:57:34 UTC Re: [CAD_CAM_EDM_DRO] Pulse Gen ballendo@y... 2000-12-09 13:19:31 UTC Re: Pulse Gen ballendo@y... 2000-12-09 13:28:03 UTC Re: Pulse Gen ballendo@y... 2000-12-09 14:46:59 UTC Re: Re: Pulse Gen