CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: CNC Router Plans

Posted by jesse
on 2001-01-09 08:35:21 UTC
You may want to look at :

http://www.diversi-tech.com/autorout.htm

This is a very simple system , a good starting point that can be adapted to a larger size and larger router motors.

Jesse

"John D. Guenther" wrote:

> I will be cutting 3/4" and thinner MDF and plywood. Multiple passes
> to achieve this are ok since this will not be a "production"
> environment, just a home shop.
>
> John
>
> --- In CAD_CAM_EDM_DRO@egroups.com, cnc002@a... wrote:
> > John:
> >
> > How thick is the MDF, Plywood etc you are planning to cut? A 1.5 Hp
> motor
> > sounds very small unless you are planning to cut at very very slow
> speeds,
> > and that includes the spindle speed. Typically you would cut those
> materials
> > at 12,000 to 20,000 RPM and feed speeds of up to 300 inches per
> minute in
> > order to get clean burn free cuts. Typically the smaller and less
> expensive
> > machines have at a minimum 3 HP and 7.5 to 10 Hp is preferred,
> especially if
> > you are ever going to consider cutting solid wood.
> >
> > I have been installing and servicing industrial Woodworking
> Machinery,
> > specializing in CNC machines, for over 15 years so if I can be of
> any
> > assistance just let me know, my E-mail address is cnc002@a...
> >
> > Randy Abernathy
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager

Discussion Thread

John D. Guenther 2001-01-08 13:57:06 UTC CNC Router Plans cnc002@a... 2001-01-08 16:37:41 UTC Re: [CAD_CAM_EDM_DRO] CNC Router Plans Bob Campbell 2001-01-08 17:46:22 UTC Re: [CAD_CAM_EDM_DRO] CNC Router Plans John D. Guenther 2001-01-09 05:39:07 UTC Re: CNC Router Plans jesse 2001-01-09 08:35:21 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC Router Plans jesse 2001-01-09 08:36:09 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC Router Plans cnc002@a... 2001-01-09 11:29:01 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC Router Plans ballendo@y... 2001-01-09 15:04:53 UTC re:Re: Re: CNC Router Plans Tim McCoy 2005-06-01 10:22:14 UTC CNC Router Plans robert monahan 2005-06-01 21:43:07 UTC Re: [CAD_CAM_EDM_DRO] CNC Router Plans