Re: [CAD_CAM_EDM_DRO] DIY anodizing
Posted by
Jon Anderson
on 2001-01-30 12:44:23 UTC
Terry,
(and Carlos), any info on anodizing would be of interest to me as well.
Especially if it's not too huge a hassle to be able to do black and
clear, and possible to generate a commercial quality finish. I'd sure
like to be able to do small lots in house instead of paying a plater $60
to anodize two parts I can hold in my hand.
Jon
(and Carlos), any info on anodizing would be of interest to me as well.
Especially if it's not too huge a hassle to be able to do black and
clear, and possible to generate a commercial quality finish. I'd sure
like to be able to do small lots in house instead of paying a plater $60
to anodize two parts I can hold in my hand.
Jon
Discussion Thread
Carlos Guillermo
2001-01-30 07:43:44 UTC
DIY anodizing
James Owens
2001-01-30 10:48:00 UTC
Re: [CAD_CAM_EDM_DRO] DIY anodizing
joelulaw@y...
2001-01-30 11:42:30 UTC
Re: DIY anodizing
Jon Anderson
2001-01-30 12:44:23 UTC
Re: [CAD_CAM_EDM_DRO] DIY anodizing
tmay@u...
2001-01-30 12:46:52 UTC
Re: DIY anodizing
Carlos Guillermo
2001-01-30 17:02:33 UTC
DIY anodizing
Carlos Guillermo
2001-01-30 17:20:30 UTC
RE: [CAD_CAM_EDM_DRO] DIY anodizing
JanRwl@A...
2001-01-30 17:55:01 UTC
Re: [CAD_CAM_EDM_DRO] DIY anodizing
Jon Anderson
2001-01-30 18:13:42 UTC
Re: [CAD_CAM_EDM_DRO] DIY anodizing
Sven Peter, TAD S.A.
2001-01-30 19:58:51 UTC
Re: [CAD_CAM_EDM_DRO] DIY anodizing
Carlos Guillermo
2001-01-30 21:01:50 UTC
RE: [CAD_CAM_EDM_DRO] DIY anodizing
dave engvall
2001-01-30 21:11:39 UTC
Re: [CAD_CAM_EDM_DRO] DIY anodizing
Jon Anderson
2001-01-30 21:16:08 UTC
Re: [CAD_CAM_EDM_DRO] DIY anodizing
ballendo@y...
2001-01-31 02:26:43 UTC
re: Re: DIY anodizing
ballendo@y...
2001-01-31 03:07:40 UTC
re:DIY anodizing
Greg Nuspel
2001-01-31 03:35:20 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
Carlos Guillermo
2001-01-31 06:38:23 UTC
RE: [CAD_CAM_EDM_DRO] re:DIY anodizing
Jon Anderson
2001-01-31 07:41:53 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
ptengin@a...
2001-01-31 09:29:50 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
dave engvall
2001-01-31 09:51:30 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
CMKTRICK@A...
2001-01-31 09:59:29 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
dave engvall
2001-01-31 10:17:59 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
Jon Anderson
2001-01-31 11:14:28 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
Smoke
2001-01-31 13:19:48 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
dave engvall
2001-01-31 13:20:41 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
Randy Gordon-Gilmore
2001-01-31 14:00:46 UTC
Epoxy, was re:DIY anodizing
psp@p...
2001-01-31 14:10:11 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
ballendo@y...
2001-01-31 14:18:23 UTC
Re: re:DIY anodizing (what is HARD anodising?)
Tim Goldstein
2001-01-31 14:23:04 UTC
Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing
Smoke
2001-01-31 14:50:17 UTC
Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing
Randy Gordon-Gilmore
2001-01-31 14:54:30 UTC
Re: Epoxy, was re:DIY anodizing
Jon Anderson
2001-01-31 15:20:21 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
Jon Anderson
2001-01-31 15:22:20 UTC
Re: [CAD_CAM_EDM_DRO] re:DIY anodizing
dave engvall
2001-01-31 19:36:40 UTC
Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing
Smoke
2001-01-31 20:28:08 UTC
Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing
dave engvall
2001-01-31 20:49:04 UTC
Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing
Smoke
2001-02-10 09:31:49 UTC
Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing