CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] DIY anodizing

on 2001-01-30 19:58:51 UTC
Well, anodizing is written on another page. Even the comercial anodizers have big problems to
keep a constant quality. Any little contamination in the baths (specialy silicium what you have in many
aluminum alloys) (more than 12 different highly corrosive chemicals for plain black) gives a horrible finish. The current you need
is not at all little.
Big shops normally donĀ“t accept tiny work because they fear to spill their bath. And the small ones
work frequently for Jewelers and so they charge.

According to an old saying: "One Hand washes the other."
Get a personel contact to somebody relevant in a big shop, ask him about the right aluminum they use and make a repair for him for a
realy good price or for free. And he will put your few pieces on the rack.

You will be better off not to invest in your own line for just a few pieces.

Good Luck
Sven Peterte:



[Non-text portions of this message have been removed]

Discussion Thread

Carlos Guillermo 2001-01-30 07:43:44 UTC DIY anodizing James Owens 2001-01-30 10:48:00 UTC Re: [CAD_CAM_EDM_DRO] DIY anodizing joelulaw@y... 2001-01-30 11:42:30 UTC Re: DIY anodizing Jon Anderson 2001-01-30 12:44:23 UTC Re: [CAD_CAM_EDM_DRO] DIY anodizing tmay@u... 2001-01-30 12:46:52 UTC Re: DIY anodizing Carlos Guillermo 2001-01-30 17:02:33 UTC DIY anodizing Carlos Guillermo 2001-01-30 17:20:30 UTC RE: [CAD_CAM_EDM_DRO] DIY anodizing JanRwl@A... 2001-01-30 17:55:01 UTC Re: [CAD_CAM_EDM_DRO] DIY anodizing Jon Anderson 2001-01-30 18:13:42 UTC Re: [CAD_CAM_EDM_DRO] DIY anodizing Sven Peter, TAD S.A. 2001-01-30 19:58:51 UTC Re: [CAD_CAM_EDM_DRO] DIY anodizing Carlos Guillermo 2001-01-30 21:01:50 UTC RE: [CAD_CAM_EDM_DRO] DIY anodizing dave engvall 2001-01-30 21:11:39 UTC Re: [CAD_CAM_EDM_DRO] DIY anodizing Jon Anderson 2001-01-30 21:16:08 UTC Re: [CAD_CAM_EDM_DRO] DIY anodizing ballendo@y... 2001-01-31 02:26:43 UTC re: Re: DIY anodizing ballendo@y... 2001-01-31 03:07:40 UTC re:DIY anodizing Greg Nuspel 2001-01-31 03:35:20 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing Carlos Guillermo 2001-01-31 06:38:23 UTC RE: [CAD_CAM_EDM_DRO] re:DIY anodizing Jon Anderson 2001-01-31 07:41:53 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing ptengin@a... 2001-01-31 09:29:50 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing dave engvall 2001-01-31 09:51:30 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing CMKTRICK@A... 2001-01-31 09:59:29 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing dave engvall 2001-01-31 10:17:59 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing Jon Anderson 2001-01-31 11:14:28 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing Smoke 2001-01-31 13:19:48 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing dave engvall 2001-01-31 13:20:41 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing Randy Gordon-Gilmore 2001-01-31 14:00:46 UTC Epoxy, was re:DIY anodizing psp@p... 2001-01-31 14:10:11 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing ballendo@y... 2001-01-31 14:18:23 UTC Re: re:DIY anodizing (what is HARD anodising?) Tim Goldstein 2001-01-31 14:23:04 UTC Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing Smoke 2001-01-31 14:50:17 UTC Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing Randy Gordon-Gilmore 2001-01-31 14:54:30 UTC Re: Epoxy, was re:DIY anodizing Jon Anderson 2001-01-31 15:20:21 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing Jon Anderson 2001-01-31 15:22:20 UTC Re: [CAD_CAM_EDM_DRO] re:DIY anodizing dave engvall 2001-01-31 19:36:40 UTC Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing Smoke 2001-01-31 20:28:08 UTC Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing dave engvall 2001-01-31 20:49:04 UTC Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing Smoke 2001-02-10 09:31:49 UTC Re: [CAD_CAM_EDM_DRO] Epoxy, was re:DIY anodizing