CAD CAM EDM DRO - Yahoo Group Archive

nut backlash comp. was re:Re: Ball screws for CNC plasma cutters

Posted by ballendo@y...
on 2001-02-16 16:04:05 UTC
Ian,

This is similar to the anti-backlash nuts used in the import
mill/drills. They use a long nut, with a slit near one end (making
two separate "thread bearing" areas). The slit does not go all the
way through, so there is no alignment problem. Anyway, there is a
backlash adjustment screw on one side of the 'main' leadscrew which
is positioned to "squeeze" the slit closed. Like your approach, this
will eliminate backlash. For awhile. THEN,...

You will have to re-adjust the screw(s). On some machines this is not
a problem (sherline, manual mills), but on a cnc it becomes (rather
quickly, IMO) a chore...

This is why some form of 'continuing' compensation is advisable, IMO.

Hope this helps.

Ballendo

P.S. Ron G previously reported good results in the backlash
department with the moglice/philly resins nuts(on a sherline; and was
gonna do a griz minimill). Ron, How are they holding up under use?


--- In CAD_CAM_EDM_DRO@y..., "Ian Wright" <Ian@i...> wrote:
> The way I am tackling this problem on the little mill I'm making
where it
> seems to be Ok is to use screws instead of the spring. <snip>

Discussion Thread

Smoke 2001-02-12 15:41:56 UTC Re: Ball screws for CNC plasma cutters Tim Goldstein 2001-02-12 15:52:25 UTC RE: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Jay Hayes 2001-02-12 16:37:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Helen Fahy 2001-02-12 20:32:54 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Jay Hayes 2001-02-12 22:28:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Helen Fahy 2001-02-13 03:27:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Joe Vicars 2001-02-13 05:23:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Sven Peter, TAD S.A. 2001-02-13 10:44:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Rich D. 2001-02-13 12:31:54 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Sven Peter, TAD S.A. 2001-02-14 03:57:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Sven Peter, TAD S.A. 2001-02-14 05:31:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Smoke 2001-02-14 14:45:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Smoke 2001-02-15 20:15:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters ballendo@y... 2001-02-15 22:22:40 UTC re:Re: Ball screws for CNC plasma cutters Tom Eldredge 2001-02-16 03:32:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Ball screws for CNC plasma cutters Ian Wright 2001-02-16 05:37:25 UTC Re: [CAD_CAM_EDM_DRO] re:Re: Ball screws for CNC plasma cutters Smoke 2001-02-16 13:08:28 UTC Re: [CAD_CAM_EDM_DRO] re:Re: Ball screws for CNC plasma cutters ballendo@y... 2001-02-16 16:04:05 UTC nut backlash comp. was re:Re: Ball screws for CNC plasma cutters ballendo@y... 2001-02-16 17:15:47 UTC backlash comped nut design re:Re: Ball screws for CNC plasma cutters Smoke 2001-02-16 20:48:30 UTC Re: [CAD_CAM_EDM_DRO] backlash comped nut design re:Re: Ball screws for CNC plasma cutters Ian Wright 2001-02-17 03:54:47 UTC Re: [CAD_CAM_EDM_DRO] nut backlash comp. was re:Re: Ball screws for CNC plasma cutters