CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion?

on 2001-02-21 19:11:04 UTC
Ian,
it is not as bad as you say, but anyway I am as stubborn as you.
I calculate a motor in kilowatt and afterwards I have to translate it into
horsepower to visualize the result to myself.
With a Neton meter you have 100g chocolate hanging on a 1 meter long bar.
Does your hand reach?

Sven Peter

Ian Wright wrote:

> ----- Original Message -----
> From: <e.heritage@...>
>
> > Why aren't steppers measure in newton meters of torque? It'd be easier for
> > everyone wouldn't it?
>
> So what's them then??? I know what an ounce is and an inch and I can make an
> arm 'x' inches long and hang a weight of 'y' ounces on it but I'm damned if
> I've ever seen a Newton I could hang on a metre long bar. Might as well use
> Btu's per fortnight - just as understandable as Newton metres.
>
> Ian
> --
> Ian W. Wright
> Sheffield UK
> www.iw63.freeserve.co.uk
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/


[Non-text portions of this message have been removed]

Discussion Thread

tnorris@h... 2001-02-19 20:17:56 UTC gm-cm to oz/inches conversion? carlcnc@s... 2001-02-19 20:56:48 UTC Re: gm-cm to oz/inches conversion? e.heritage@b... 2001-02-20 03:26:45 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? klaus@s... 2001-02-20 15:40:44 UTC Re: gm-cm to oz/inches conversion? ballendo@y... 2001-02-20 21:17:43 UTC Re: gm-cm to oz/inches conversion? ballendo@y... 2001-02-20 21:57:39 UTC Re: gm-cm to oz/inches conversion? alexskopal@y... 2001-02-20 23:29:51 UTC Re: gm-cm to oz/inches conversion? Ian Wright 2001-02-21 02:13:29 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? carlcnc@s... 2001-02-21 04:51:21 UTC Re: gm-cm to oz/inches conversion? e.heritage@b... 2001-02-21 14:08:13 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? ballendo@y... 2001-02-21 14:13:50 UTC Re: gm-cm to oz/inches conversion? machines@n... 2001-02-21 14:52:56 UTC Re: gm-cm to oz/inches conversion? machines@n... 2001-02-21 15:07:51 UTC Re: gm-cm to oz/inches conversion? Sven Peter, TAD S.A. 2001-02-21 19:11:04 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? Greg Jackson 2001-02-21 20:59:09 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? Ian Wright 2001-02-22 08:50:45 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? e.heritage@b... 2001-02-22 11:05:14 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? Ian Wright 2001-02-22 13:07:07 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? e.heritage@b... 2001-02-22 13:57:54 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? davemucha@j... 2001-02-22 14:23:02 UTC Mars probe (was Re: gm-cm to oz/inches conversion?) e.heritage@b... 2001-02-22 15:04:42 UTC Re: [CAD_CAM_EDM_DRO] Mars probe (was Re: gm-cm to oz/inches conversion?) Randy Gordon-Gilmore 2001-02-22 15:34:23 UTC Way off topic: Olfactory detection and asteroid probes dave engvall 2001-02-22 17:33:00 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? JanRwl@A... 2001-02-22 17:55:17 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? dave engvall 2001-02-22 18:01:32 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? e.heritage@b... 2001-02-23 03:32:35 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? davemucha@j... 2001-02-23 04:19:36 UTC microns of vac (was Re: gm-cm to oz/inches conversion? davemucha@j... 2001-02-23 04:56:53 UTC Re: gm-cm to oz/inches conversion? Tony Jeffree 2001-02-23 07:46:40 UTC Re: gm-cm to oz/inches conversion? dave engvall 2001-02-23 09:22:19 UTC Re: [CAD_CAM_EDM_DRO] Re: gm-cm to oz/inches conversion? davemucha@j... 2001-02-23 11:29:43 UTC Re: gm-cm to oz/inches conversion?