CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] cutting speed and feed for 3/4" dovetail cutter

Posted by Bill Darby
on 2001-03-04 22:04:37 UTC
There is a nice little program that I just downloaded free
called "CIMCO Speed and feed UK" from
http://www.virtualmachinist.com/ It does all the math that
Jon just showed you but it does not tell you the acceptable
surface speed to run using a particular type of cutter on a
particular material and or coolant requirements. (if it does I
did not see it, but mind,,, I am operating at about 20% with
the flu right now)

marble_h@... wrote:
>
> Can anyone tell me what the feed and cutting speed is for it
>
> I have been cutting at 160 rpm's and a feed of .002 per rev but I
> snapped the cutter ,boy $59.00 down the drain and I have 15 more cuts
> to do..
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

marble_h@y... 2001-03-04 16:52:34 UTC cutting speed and feed for 3/4" dovetail cutter Brian Pitt 2001-03-04 17:41:27 UTC Re: [CAD_CAM_EDM_DRO] cutting speed and feed for 3/4" dovetail cutter Jon Anderson 2001-03-04 18:09:13 UTC Re: [CAD_CAM_EDM_DRO] cutting speed and feed for 3/4" dovetail cutter Jon Elson 2001-03-04 21:48:12 UTC Re: [CAD_CAM_EDM_DRO] cutting speed and feed for 3/4" dovetail cutter Bill Darby 2001-03-04 22:04:37 UTC Re: [CAD_CAM_EDM_DRO] cutting speed and feed for 3/4" dovetail cutter marble here 2001-03-05 02:34:58 UTC Re: [CAD_CAM_EDM_DRO] cutting speed and feed for 3/4" dovetail cutter Jon Anderson 2001-03-05 07:04:10 UTC Re: [CAD_CAM_EDM_DRO] cutting speed and feed for 3/4" dovetail cutter Jon Elson 2001-03-05 11:35:29 UTC Re: [CAD_CAM_EDM_DRO] cutting speed and feed for 3/4" dovetail cutter John Stevenson 2001-03-05 15:48:22 UTC Re: cutting speed and feed for 3/4" dovetail cutter marble here 2001-03-05 19:41:12 UTC Re: [CAD_CAM_EDM_DRO] Re: cutting speed and feed for 3/4" dovetail cutter marble here 2001-03-05 19:44:09 UTC Re: [CAD_CAM_EDM_DRO] cutting speed and feed for 3/4" dovetail cutter ballendo@y... 2001-03-06 05:18:37 UTC moly-dee ??? was Re: cutting speed and feed for 3/4" dovetail cutter Tim Goldstein 2001-03-06 05:32:56 UTC RE: [CAD_CAM_EDM_DRO] moly-dee ??? was Re: cutting speed and feed for 3/4" dovetail cutter