Re: [CAD_CAM_EDM_DRO] Re: CNCpro VS Artisan VS flashcut

You find it at any shoe store. Just get a new pair of sneakers and you have
a new sneaker net.
Then grab a floppy and walk it to the machine.

later,
Larry E.

----- Original Message -----
From: <cadman@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Tuesday, April 03, 2001 11:56 PM
Subject: [CAD_CAM_EDM_DRO] Re: CNCpro VS Artisan VS flashcut


> Where do you find "sneakernet"? I looked on M$ ftp site.
>
> CADMAN
>
> --- In CAD_CAM_EDM_DRO@y..., "Larry Edington" <ledington@c...> wrote:
> > Yea, there are ways to network the DOS box. But it's just
> > not worth the trouble to me. I lived
> > through networking from Netware days to Windows days. I've
> > run several DOS machines on
> > a network. I shall NOT go back to those headaches ever
> > again. So sneakernet is the easiest
> > and most trouble free solution until all my Cnc controls are
> > Windows based.
> >
> > later,
> > Larry E.
> >
> > ----- Original Message -----
> > From: <cla@m...>
> > To: <CAD_CAM_EDM_DRO@y...>
> > Sent: Tuesday, April 03, 2001 3:23 PM
> > Subject: Re: [CAD_CAM_EDM_DRO] CNCpro VS Artisan VS flashcut
> >
> >
> > > > sneaker net since I have to use floppies
> > > > with the DOS based machines.
> > >
> > > This might be of some help to you. If you FTP to
> > Microsoft you should be
> > > able to find a freely available DOS Microsoft Network
> > program. I don't
> > > remember what it is called exactly and it was a few years
> > back that I got
> > > it. But it will allow you to network to your DOS machines.
> > I used on one of
> > > my machines some time back. If fact, if you can't locate
> > it I may be able
> > > to find it and email it to you.
> > >
> > > Claton Cadmus
> > >
> > >
> > > Welcome to CAD_CAM_EDM_DRO@e...,an unmoderated list
> > for the discussion of shop built systems, for CAD, CAM, EDM,
> > and DRO.
> > >
> > > Addresses:
> > > Post message: CAD_CAM_EDM_DRO@y...
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > > List owner: CAD_CAM_EDM_DRO-owner@y...,
> > wanliker@a...
> > > Moderator: jmelson@a... timg@k...
> > [Moderator]
> > > URL to this page:
> > http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > bill,
> > > List Manager
> > >
> > > FAQ: http://www.ktmarketing.com/faq.html
> > >
> > > Your use of Yahoo! Groups is subject to
> > http://docs.yahoo.com/info/terms/
> > >
> > >
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>