CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Air assist on Series II knee?

Posted by Tim Goldstein
on 2001-04-30 09:05:40 UTC
It seems to me that if arranged as follows it would relieve the motor from
the weight of the table.

-----|
| |---
////|||///////
| |---
-----|

Turned sideways (OK I stink at ASCII art). Cylinder at left with a piston
that is free to rotate in the cylinder (attached firmly to the screw). The
nut is attached to the top of the outside of the cylinder. The screw itself
would be bearing the full weight of the table, but the amount that is being
carried by the nut would be offset. The screw is actually rotated from the
top to raise and lower the table and the nut is fixed. The top bearings that
attach the screw to the table would also be carrying full load.

Of course if there is anyone that actually knows how this works we could end
a lot of speculation.

Tim
[Denver, CO]


> I would be suprised if they did it this way. This would not
> relieve any pressure from the screw.
>
> Tim Goldstein wrote:
>
> > That is a novel idea. It really would not require that much
> pressure if the
> > screw was attached to a larger piston underneath. The
> piston would also keep
> > air from leaking out the cylinder. From the arrangement of
> the parts this is
> > a likely scenario.
> >
> > Tim
> > [Denver, CO]
> >
> > > Hmm, is there any chance the screw itself is the
> cylinder, or rather
> > > the piston? I'm thinking probably not, as it would require an
> > > unreasonably high air pressure to lift a heavy knee with the cross
> > > section of a typical screw. It would of course leak a
> bit, but the
> > > leaks would keep chips out of the nut.
> > >
> > > Chris
> > >
> > > FAQ: http://www.ktmarketing.com/faq.html
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list
> for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@...
> > Moderator: jmelson@... timg@...
> [Moderator]
> > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Manager
> >
> > FAQ: http://www.ktmarketing.com/faq.html
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/


Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.

Addresses:
Post message: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager

FAQ: http://www.ktmarketing.com/faq.html

Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

jeffrosselthecat@y... 2001-04-28 07:33:04 UTC jeffrosselthecat@y... 2001-04-28 07:34:41 UTC (Forgot above subject) Stepper sizing Tim Goldstein 2001-04-28 08:07:02 UTC RE: [CAD_CAM_EDM_DRO] (unknown) jeffrosselthecat@y... 2001-04-28 11:10:03 UTC Re: (unknown) mini mill size afogassa@y... 2001-04-28 20:58:34 UTC Tim Goldstein 2001-04-28 22:00:16 UTC Air assist on Series II knee? Sven Peter, TAD S.A. 2001-04-29 09:05:24 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Tim Goldstein 2001-04-29 16:27:33 UTC RE: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Brian Pitt 2001-04-29 16:53:33 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Tim Goldstein 2001-04-29 17:09:52 UTC RE: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Sven Peter, TAD S.A. 2001-04-30 05:35:58 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? stratton@m... 2001-04-30 08:00:47 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Tim Goldstein 2001-04-30 08:34:38 UTC RE: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Joe Vicars 2001-04-30 08:37:33 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Tim Goldstein 2001-04-30 09:05:40 UTC RE: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Joe Vicars 2001-04-30 09:32:47 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? indigo_red@q... 2001-04-30 09:34:53 UTC Re: Air assist on Series II knee? Jon Elson 2001-05-01 15:39:34 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Ian Wright 2001-05-02 01:10:17 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Keith Rumley 2001-05-04 08:01:15 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee?