CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee?

Posted by Ian Wright
on 2001-05-02 01:10:17 UTC
----- Original Message ----- >
> Well, 40 PSI equals the weight of the knee minus the drag of the stepper
> and leadscrew. It is hard to guess the relative proportions of drag and
> weight. You might try turning down the motor current and adjust air
> pressure until the motor stalls evenly in both directions. Or, you
> could disconnect the motor mechanically and find the balance pressure.

Hi,

Surely the pressure should be adjusted for each job to compensate for the
weight of the part being machined, or, at least, set to an 'average' figure
two or three ponds above the weight of the knee etc.

Ian
--
Ian W. Wright
Sheffield UK
www.iw63.freeserve.co.uk

Discussion Thread

jeffrosselthecat@y... 2001-04-28 07:33:04 UTC jeffrosselthecat@y... 2001-04-28 07:34:41 UTC (Forgot above subject) Stepper sizing Tim Goldstein 2001-04-28 08:07:02 UTC RE: [CAD_CAM_EDM_DRO] (unknown) jeffrosselthecat@y... 2001-04-28 11:10:03 UTC Re: (unknown) mini mill size afogassa@y... 2001-04-28 20:58:34 UTC Tim Goldstein 2001-04-28 22:00:16 UTC Air assist on Series II knee? Sven Peter, TAD S.A. 2001-04-29 09:05:24 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Tim Goldstein 2001-04-29 16:27:33 UTC RE: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Brian Pitt 2001-04-29 16:53:33 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Tim Goldstein 2001-04-29 17:09:52 UTC RE: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Sven Peter, TAD S.A. 2001-04-30 05:35:58 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? stratton@m... 2001-04-30 08:00:47 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Tim Goldstein 2001-04-30 08:34:38 UTC RE: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Joe Vicars 2001-04-30 08:37:33 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Tim Goldstein 2001-04-30 09:05:40 UTC RE: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Joe Vicars 2001-04-30 09:32:47 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? indigo_red@q... 2001-04-30 09:34:53 UTC Re: Air assist on Series II knee? Jon Elson 2001-05-01 15:39:34 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Ian Wright 2001-05-02 01:10:17 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee? Keith Rumley 2001-05-04 08:01:15 UTC Re: [CAD_CAM_EDM_DRO] Air assist on Series II knee?