CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] way covers

Posted by Smoke
on 2001-05-01 23:19:42 UTC
Wonder if there's an easy/cheap way to make a round bellows from RTV, latex
rubber or whatever?

Anyone have any ideas?

Smoke
-----Original Message-----
From: Jon Elson <jmelson@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com <CAD_CAM_EDM_DRO@yahoogroups.com>
Date: Tuesday, May 01, 2001 5:45 PM
Subject: Re: [CAD_CAM_EDM_DRO] way covers


>
>
>Smoke wrote:
>
>> Cancel my last question about the flat springs. just went to the hennig
>> site listed below and they have them. The items are know as telescoping
>> (steel) springs.
>>
>> Gortite has some round bellows for covering ball screws and nuts that
might
>> work too.
>
>Yup, and they are $200 for a relatively short length, too! Our shop got a
quote
>to replace some.
>
>If you get a price on the Hennig springs, please let us know. I have some
unguarded
>ball screws. They were originally protected by the Gortite bellows, but
the grease
>rotted them into crumbly bits.
>
>Thanks,
>
>Jon
>
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>FAQ: http://www.ktmarketing.com/faq.html
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>

Discussion Thread

Joe Vicars 2001-04-30 09:47:22 UTC way covers Brian Pitt 2001-04-30 10:47:40 UTC Re: [CAD_CAM_EDM_DRO] way covers Smoke 2001-04-30 20:43:44 UTC Re: [CAD_CAM_EDM_DRO] way covers Smoke 2001-04-30 21:23:49 UTC Re: [CAD_CAM_EDM_DRO] way covers JanRwl@A... 2001-04-30 22:20:08 UTC Re: [CAD_CAM_EDM_DRO] way covers Jon Elson 2001-05-01 16:44:12 UTC Re: [CAD_CAM_EDM_DRO] way covers Smoke 2001-05-01 23:19:42 UTC Re: [CAD_CAM_EDM_DRO] way covers ballendo@y... 2001-05-02 08:39:48 UTC Re: way covers Brian Pitt 2001-05-02 12:08:21 UTC Re: [CAD_CAM_EDM_DRO] way covers Alan Marconett KM6VV 2001-05-02 14:06:28 UTC Re: [CAD_CAM_EDM_DRO] way covers Jon Elson 2001-05-02 14:35:59 UTC Re: [CAD_CAM_EDM_DRO] way covers Joe Vicars 2001-05-02 15:29:57 UTC Re: [CAD_CAM_EDM_DRO] way covers Brian Pitt 2001-05-03 11:44:00 UTC Re: [CAD_CAM_EDM_DRO] way covers Graeme Murray 2001-05-03 13:41:41 UTC Re: [CAD_CAM_EDM_DRO] way covers Alan Marconett KM6VV 2001-05-03 14:56:16 UTC Re: [CAD_CAM_EDM_DRO] way covers Alan Marconett KM6VV 2001-05-03 15:20:53 UTC Re: [CAD_CAM_EDM_DRO] way covers Tom Eldredge 2001-05-04 10:43:49 UTC Re: [CAD_CAM_EDM_DRO] way covers designer987@y... 2001-11-06 18:04:06 UTC Re: way covers Garry & Maxine Foster 2003-01-12 14:06:54 UTC HobbyCNC