CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] way covers

Posted by Graeme Murray
on 2001-05-03 13:41:41 UTC
Hi folks
I made bellows for a photographic enlarger I built about 43 years ago .
I still have it downstairs where I now use it as a light source for part of
my printed circuit prototyping system.
It was not too big a deal to fold from coated fabric as I remember . I
could probably draw something if anyone feels they need it, but I wont do it
with "asci art " as I think it is called . I also have done a quill drive on
my mill ( 50 x 10 table size ) that I will do a picture of if people are
interested , it is working quite well.
I have learned quite a lot from you folk on the group so I hope to put a bit
back in as time allows.
Regards
Graeme
( Kiwi from down under)
>
> yes,there was the link on making camera bellows from before
> http://www.cyberbeach.net/~dbardell/bellows.html
> if the corner pleats were made larger it would make an octagon
> shaped 'sorta round' ball screw cover
>
> does anyone else think we might be trying to 'Macho' our way thru
> making a pleated skirt for the machine?
> is someones wife sitting at her sewing machine laughing ?
> I hear laughter ;-)
>

Discussion Thread

Joe Vicars 2001-04-30 09:47:22 UTC way covers Brian Pitt 2001-04-30 10:47:40 UTC Re: [CAD_CAM_EDM_DRO] way covers Smoke 2001-04-30 20:43:44 UTC Re: [CAD_CAM_EDM_DRO] way covers Smoke 2001-04-30 21:23:49 UTC Re: [CAD_CAM_EDM_DRO] way covers JanRwl@A... 2001-04-30 22:20:08 UTC Re: [CAD_CAM_EDM_DRO] way covers Jon Elson 2001-05-01 16:44:12 UTC Re: [CAD_CAM_EDM_DRO] way covers Smoke 2001-05-01 23:19:42 UTC Re: [CAD_CAM_EDM_DRO] way covers ballendo@y... 2001-05-02 08:39:48 UTC Re: way covers Brian Pitt 2001-05-02 12:08:21 UTC Re: [CAD_CAM_EDM_DRO] way covers Alan Marconett KM6VV 2001-05-02 14:06:28 UTC Re: [CAD_CAM_EDM_DRO] way covers Jon Elson 2001-05-02 14:35:59 UTC Re: [CAD_CAM_EDM_DRO] way covers Joe Vicars 2001-05-02 15:29:57 UTC Re: [CAD_CAM_EDM_DRO] way covers Brian Pitt 2001-05-03 11:44:00 UTC Re: [CAD_CAM_EDM_DRO] way covers Graeme Murray 2001-05-03 13:41:41 UTC Re: [CAD_CAM_EDM_DRO] way covers Alan Marconett KM6VV 2001-05-03 14:56:16 UTC Re: [CAD_CAM_EDM_DRO] way covers Alan Marconett KM6VV 2001-05-03 15:20:53 UTC Re: [CAD_CAM_EDM_DRO] way covers Tom Eldredge 2001-05-04 10:43:49 UTC Re: [CAD_CAM_EDM_DRO] way covers designer987@y... 2001-11-06 18:04:06 UTC Re: way covers Garry & Maxine Foster 2003-01-12 14:06:54 UTC HobbyCNC