Re: [CAD_CAM_EDM_DRO] way covers
Posted by
Tom Eldredge
on 2001-05-04 10:43:49 UTC
Graeme,
This would be useful. Almost everyone needs some sort of flexible cover for
some part of a machine.
Tom Eldredge
This would be useful. Almost everyone needs some sort of flexible cover for
some part of a machine.
Tom Eldredge
----- Original Message -----
From: Graeme Murray <graemem@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, May 03, 2001 3:44 PM
Subject: Re: [CAD_CAM_EDM_DRO] way covers
> Hi folks
> I made bellows for a photographic enlarger I built about 43 years ago .
> I still have it downstairs where I now use it as a light source for part
of
> my printed circuit prototyping system.
> It was not too big a deal to fold from coated fabric as I remember . I
> could probably draw something if anyone feels they need it, but I wont do
it
> with "asci art " as I think it is called . I also have done a quill drive
on
> my mill ( 50 x 10 table size ) that I will do a picture of if people are
> interested , it is working quite well.
> I have learned quite a lot from you folk on the group so I hope to put a
bit
> back in as time allows.
> Regards
> Graeme
> ( Kiwi from down under)
> >
> > yes,there was the link on making camera bellows from before
> > http://www.cyberbeach.net/~dbardell/bellows.html
> > if the corner pleats were made larger it would make an octagon
> > shaped 'sorta round' ball screw cover
> >
> > does anyone else think we might be trying to 'Macho' our way thru
> > making a pleated skirt for the machine?
> > is someones wife sitting at her sewing machine laughing ?
> > I hear laughter ;-)
> >
>
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
Discussion Thread
Joe Vicars
2001-04-30 09:47:22 UTC
way covers
Brian Pitt
2001-04-30 10:47:40 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Smoke
2001-04-30 20:43:44 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Smoke
2001-04-30 21:23:49 UTC
Re: [CAD_CAM_EDM_DRO] way covers
JanRwl@A...
2001-04-30 22:20:08 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Jon Elson
2001-05-01 16:44:12 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Smoke
2001-05-01 23:19:42 UTC
Re: [CAD_CAM_EDM_DRO] way covers
ballendo@y...
2001-05-02 08:39:48 UTC
Re: way covers
Brian Pitt
2001-05-02 12:08:21 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Alan Marconett KM6VV
2001-05-02 14:06:28 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Jon Elson
2001-05-02 14:35:59 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Joe Vicars
2001-05-02 15:29:57 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Brian Pitt
2001-05-03 11:44:00 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Graeme Murray
2001-05-03 13:41:41 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Alan Marconett KM6VV
2001-05-03 14:56:16 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Alan Marconett KM6VV
2001-05-03 15:20:53 UTC
Re: [CAD_CAM_EDM_DRO] way covers
Tom Eldredge
2001-05-04 10:43:49 UTC
Re: [CAD_CAM_EDM_DRO] way covers
designer987@y...
2001-11-06 18:04:06 UTC
Re: way covers
Garry & Maxine Foster
2003-01-12 14:06:54 UTC
HobbyCNC