Re: [CAD_CAM_EDM_DRO] Inserts R US
Posted by
Brian Pitt
on 2001-05-05 01:35:10 UTC
for carbides the tool nose should be at dead center height on both
positive and negative rake tool holders
one trick is to set the tool low and make a light facing cut
then mesure the stump it leaves on the bar and shim the tool holder up by
half the stump diameter, that will get it within a few 'tenths' of center
Brian
positive and negative rake tool holders
one trick is to set the tool low and make a light facing cut
then mesure the stump it leaves on the bar and shim the tool holder up by
half the stump diameter, that will get it within a few 'tenths' of center
Brian
> I just yesterday purchased a tool and insert combination to face finish
> aluminum disks. It is a VNMG carbide insert, and I am using an MVJNR163D
> tool holder, at the advice of a friend. I suppose your comment relates to
> the height of the tool in relation to center? This tool holder has a
> "negative rake", I think it is called. How do I know just where the tool
> should be vertically when turning on a lathe? Should the tool touch the
> work exactly at the height of the center of the disk being cut? I suppose
> this is elementary, but I hack things out on a taig lathe when I need them,
> and I really do not know what is best.
> Thanks again.
>
> Tom Eldredge
Discussion Thread
jvicars@c...
2001-04-27 20:31:32 UTC
Inserts R US
JanRwl@A...
2001-04-27 20:43:29 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
Jon Anderson
2001-04-27 20:50:31 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
jvicars@c...
2001-04-27 21:06:29 UTC
Re: Inserts R US
Sven Peter, TAD S.A.
2001-04-27 21:10:02 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
Brian Pitt
2001-04-27 23:44:42 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
Robert Allen & Marsha Camp
2001-04-28 04:03:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Inserts R US
Jon Anderson
2001-04-28 07:56:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Inserts R US
dave engvall
2001-04-29 21:23:24 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
Tom Eldredge
2001-05-03 17:50:26 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
Brian Pitt
2001-05-05 01:35:10 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
Sven Peter, TAD S.A.
2001-05-08 08:39:11 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
Terry Toddy
2001-05-08 11:02:33 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
Sven Peter, TAD S.A.
2001-05-08 12:59:59 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
Tom Eldredge
2001-05-08 13:13:32 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US
Terry Toddy
2001-05-08 14:16:19 UTC
Re: [CAD_CAM_EDM_DRO] Inserts R US