CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] machining ballscrews

Posted by Mike
on 2001-05-09 13:03:41 UTC
I've had good success with cubic boron inserts. Had a couple of "demo"
inserts in CNMG style and TPMR style.

gaffer




>Howdy
> I recently acquired a nice mill[Kasuga] and am wondering if anyone
>has tried this:
> Use a small lathe mounted on the mill table [maybe just the
>headstock] to hold and slowly turn the screw while grinding the end
>with apropriate cup wheel mounted in the mill spindle. I can run my
>spindle up to 10k rpm with inverter for short periods.
> I don't own a lathe and machinists that I have do end-machining
>always remark/complain about the hardness of screw .
> I was thinking up alternatives.
>
> Carl
>
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>FAQ: http://www.ktmarketing.com/faq.html
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/


--

Discussion Thread

carlcnc@e... 2001-05-09 06:36:00 UTC machining ballscrews Joe Vicars 2001-05-09 06:49:19 UTC Re: [CAD_CAM_EDM_DRO] machining ballscrews stratton@m... 2001-05-09 07:19:43 UTC Re: [CAD_CAM_EDM_DRO] machining ballscrews Mike 2001-05-09 13:03:41 UTC Re: [CAD_CAM_EDM_DRO] machining ballscrews Les Watts 2001-05-09 17:20:06 UTC Re: [CAD_CAM_EDM_DRO] machining ballscrews Doug Harrison 2001-05-09 19:29:42 UTC Re: [CAD_CAM_EDM_DRO] machining ballscrews ballendo@y... 2001-05-10 03:37:07 UTC Re: machining ballscrews ballendo@y... 2001-05-10 05:09:10 UTC Re: machining ballscrews stratton@m... 2001-05-10 05:55:11 UTC Re: [CAD_CAM_EDM_DRO] Re: machining ballscrews Tim Goldstein 2001-05-10 10:53:47 UTC RE: [CAD_CAM_EDM_DRO] Re: machining ballscrews Doug Harrison 2001-05-10 16:40:04 UTC Re: [CAD_CAM_EDM_DRO] Re: machining ballscrews Sven Peter, TAD S.A. 2001-05-11 12:54:21 UTC Re: [CAD_CAM_EDM_DRO] machining ballscrews ballendo@y... 2001-05-12 05:41:58 UTC Re: machining ballscrews ballendo@y... 2001-05-12 07:28:08 UTC Re: machining ballscrews