Re: [CAD_CAM_EDM_DRO] Aluminum cutting,,,,,,,
Posted by
Smoke
on 2001-06-02 13:15:11 UTC
Max speed on my mill is only about 3200 RPM and I think I'll pass on using
an 1/8" end mill when surface finishing a 5"+ wide piece or cutting 1" plus
groove widths.
Smoke
an 1/8" end mill when surface finishing a 5"+ wide piece or cutting 1" plus
groove widths.
Smoke
>I have 5 plus years in cutting aluminum at the sign co. business, I workuse
>for.... Use 50/52 type aluminum, carbide spiral up (two fluted for smooth
>clean cuts, .250" in diameter, if you need to use a small milling bit, lets
>say as small as .125", use a non-carbide single flute bit, by all means,
>either a coolant type oil or what I use, a water base coolant. Dependingon
>feed rate, use 16,000~19,000 rpm, climb direction is a must. I cut .125"discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>50/52 aluminum about anywhere from 24~28 ipm. Coolant also helps keep your
>bit cooler and last much longer.......
>
>
>Russ.
>
>
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>FAQ: http://www.ktmarketing.com/faq.html
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
Discussion Thread
RC
2001-06-02 12:21:26 UTC
Aluminum cutting,,,,,,,
Smoke
2001-06-02 13:15:11 UTC
Re: [CAD_CAM_EDM_DRO] Aluminum cutting,,,,,,,
info.host@b...
2001-06-02 14:17:43 UTC
Re: [CAD_CAM_EDM_DRO] Aluminum cutting,,,,,,,
Jon Elson
2001-06-02 21:43:05 UTC
Re: [CAD_CAM_EDM_DRO] Aluminum cutting,,,,,,,
Smoke
2001-06-03 17:38:17 UTC
Re: [CAD_CAM_EDM_DRO] Aluminum cutting,,,,,,,
Smoke
2001-06-03 17:43:15 UTC
Re: [CAD_CAM_EDM_DRO] Aluminum cutting,,,,,,,
yahoo@a...
2001-06-03 19:21:27 UTC
Re: Aluminum cutting,,,,,,,
Chris Stratton
2001-06-03 19:58:17 UTC
Re: [CAD_CAM_EDM_DRO] Aluminum cutting,,,,,,,
Smoke
2001-06-03 21:10:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Aluminum cutting,,,,,,,
Smoke
2001-06-03 21:13:30 UTC
Re: [CAD_CAM_EDM_DRO] Aluminum cutting,,,,,,,
Jon Elson
2001-06-03 21:50:33 UTC
Re: [CAD_CAM_EDM_DRO] Aluminum cutting,,,,,,,
yahoo@a...
2001-06-04 07:10:22 UTC
Re: Aluminum cutting,,,,,,,