Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Posted by
Smoke
on 2001-06-10 14:31:51 UTC
FYI....I recently got some info re some venturi type burners that don't
require forced air to operate and they put out enough heat for melting steel
a bit quicker than with the forced air units!
Will give that a try too one of these days.
How long does it take for your furnace to heat up to the point where the
iron will melt to a pourable temp?
Hope you'll visit the HomeFoundry egroup site and post some info about your
furnaces and their use. Your experience with home foundry work would be
appreciated.
Smoke
require forced air to operate and they put out enough heat for melting steel
a bit quicker than with the forced air units!
Will give that a try too one of these days.
How long does it take for your furnace to heat up to the point where the
iron will melt to a pourable temp?
Hope you'll visit the HomeFoundry egroup site and post some info about your
furnaces and their use. Your experience with home foundry work would be
appreciated.
Smoke
>with propane youamount
>must supply air for combustion.
>
>My 1st furnace was a charcoal one. I melted brass, bronze & alum. The
>of ash and burning charcoal which went flying in the air made for a greathad
>light show but pissed off the wife and made for a fire hazard if the area
>dry grass.of
>
>Since then I've built four furnaces and one cupola. My big one is made
>from a 55 gal drum and uses a Toro electric leaf blower and a 20 lbs tank
>propane for melting bronze, brass, and alum. When I melt cast iron I muston
>use a 100lbs tank or the propane will freeze up.
>
>My small one is made from a 20 lbs out of date EMPTYpropane tank that I
>filled with water and cut up with a sawzall. I can melt cast iron in this
>with just a 20lbs tank.the
>
>Lindsey Publications has several good books on building furnaces and an
>excellent one on casting titled "US NAVY FOUNDRY MANUAL".
>
>There are other newsgroup that cover casting and black smithing.
>
>
>Last but not least I've been casting parts for 14 years and have not set
>house on fire or killed myself by using common sense and following safety
>rules.
>
>
Discussion Thread
Smoke
2001-06-07 12:40:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Joe Vicars
2001-06-07 13:31:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Christopher Prosser
2001-06-07 13:52:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Pavel Korensky
2001-06-07 13:57:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Chris Stratton
2001-06-07 14:22:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
phrh@w...
2001-06-07 14:25:22 UTC
Re: melting aluminium
dholness@a...
2001-06-07 14:34:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Alan Marconett KM6VV
2001-06-07 15:54:42 UTC
Re: melting aluminium
Christopher Prosser
2001-06-07 16:03:43 UTC
Re: [CAD_CAM_EDM_DRO] [OT] melting aluminium
Alan Marconett KM6VV
2001-06-07 16:33:39 UTC
Re: [CAD_CAM_EDM_DRO] [OT] melting aluminium
Ian Wright
2001-06-07 16:40:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Lee Studley
2001-06-07 16:56:32 UTC
Re: melting aluminium
Sven Peter, TAD S.A.
2001-06-07 20:57:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
M. SHABBIR MOGHUL
2001-06-07 22:29:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Lee Studley
2001-06-07 23:55:34 UTC
Re: melting aluminium
Tim Goldstein
2001-06-08 00:01:45 UTC
Cutler-Hammer limit switch source?
info.host@b...
2001-06-08 08:49:41 UTC
Re: [CAD_CAM_EDM_DRO] [OT] melting aluminium
info.host@b...
2001-06-10 13:18:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Smoke
2001-06-10 14:17:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Smoke
2001-06-10 14:21:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Smoke
2001-06-10 14:25:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Smoke
2001-06-10 14:31:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
Smoke
2001-06-10 14:33:42 UTC
Re: [CAD_CAM_EDM_DRO] [OT] melting aluminium
Smoke
2001-06-10 14:34:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium
info.host@b...
2001-06-10 23:34:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: melting aluminium