Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Mill by Adcock and Shipley
Posted by
Tom Eldredge
on 2001-07-05 07:31:08 UTC
This is good advice from John. I believe it is a re-post of a previous post
is it not? Anyhow it is good, and ought to be repeated from time to time.
Tom Eldredge
is it not? Anyhow it is good, and ought to be repeated from time to time.
Tom Eldredge
----- Original Message -----
From: <machines@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, July 04, 2001 4:32 PM
Subject: [CAD_CAM_EDM_DRO] Re: Bridgeport Mill by Adcock and Shipley
> --- In CAD_CAM_EDM_DRO@y..., u980162@y... wrote:
> > I have a Bridgeport Milling machine of Adcock - Shipley. I am
> > planning to convert into CNC
John said:
> If this is the standard manual machine then don't convert it. It's
> not a viable proposition.
> At the moment you have a manual mill worth around 2 to $3000 at a
> guess. To convert it you need ballscrews, pressure oiling, motors,
> drivers, power supply and a controller of sorts. Add to this the lash
> up you will finish up with converting the Z axis and you will have
> spent another $2000 to $4000 depending on how lucky you are sourcing
> parts. This will then give you an investment of between $4000 and
> $7000. Your actual machine worth though will have depreciated down to
> less than $1000 as it's a one off weird special.
> There are a few people on this list who have attacked this problem
> from the opposite end. If nessesary for funds or room, sell the
> manual machine, there is a ready market and buy a Boss 1 or 2 with a
> dead controller. They are out there and they are less than $1000.
> You will then have ballscrews, pressure oiling, motors, possibly
> drive cards and a decent Z axis drive. In other words you are 75
> percent there.
> Sorry to be a wet blanket but it's all down to cost.
>
> John Stevenson.
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
Discussion Thread
u980162@y...
2001-07-04 01:18:25 UTC
Bridgeport Mill by Adcock and Shipley
machines@n...
2001-07-04 14:32:06 UTC
Re: Bridgeport Mill by Adcock and Shipley
Paul
2001-07-04 14:51:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Mill by Adcock and Shipley
Gabriel L Romeu
2001-07-04 15:58:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Mill by Adcock and Shipley
Tom Eldredge
2001-07-05 07:31:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Mill by Adcock and Shipley
David M. Munro
2001-07-05 16:15:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Mill by Adcock and Shipley
Fitch R. Williams
2001-07-05 16:32:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Mill by Adcock and Shipley
machines@n...
2001-07-05 17:35:58 UTC
Re: Bridgeport Mill by Adcock and Shipley
Jon Elson
2001-07-05 20:55:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Mill by Adcock and Shipley
hllrsr@c...
2001-07-07 02:49:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Mill by Adcock and Shipley