Re: 48V 10A! Mauch 2A board?
Posted by
ballendo@y...
on 2001-07-06 21:19:05 UTC
Hello Randy,
--- In CAD_CAM_EDM_DRO@y..., > Randy Gordon-Gilmore wrote:
>>Has anyone used a 2A board on 48V? The L298 datasheet says 46V
>>working voltage, with 50V absolute maximum. Would I be pushing
>>things too far with 48V?
YES!!! The 298's WILL "smoke" on the first power surge!
I see Dan M has answered (later post) that he has run the 298's up to
40V. Me too. But 48 is too much...
Hope this helps.
Ballendo
Discussion Thread
Bruce
2001-07-03 16:18:58 UTC
RE: Vacuum table
Randy Gordon-Gilmore
2001-07-04 17:49:13 UTC
48V 10A! Mauch 2A board?
Alan Marconett KM6VV
2001-07-04 19:16:13 UTC
Re: [CAD_CAM_EDM_DRO] 48V 10A! Mauch 2A board?
Jon Elson
2001-07-04 23:35:35 UTC
Re: [CAD_CAM_EDM_DRO] 48V 10A! Mauch 2A board?
Randy Gordon-Gilmore
2001-07-05 00:25:26 UTC
Re: 48V 10A! Mauch 2A board?
Dan Mauch
2001-07-05 10:28:06 UTC
RE: [CAD_CAM_EDM_DRO] 48V 10A! Mauch 2A board?
Alan Marconett KM6VV
2001-07-05 12:57:17 UTC
Re: [CAD_CAM_EDM_DRO] 48V 10A! Mauch 2A board?
ballendo@y...
2001-07-06 21:19:05 UTC
Re: 48V 10A! Mauch 2A board?
cncdxf@a...
2001-07-07 09:15:13 UTC
Re: 48V 10A! Mauch 2A board?
alipavsky@c...
2005-08-13 20:34:38 UTC
Vacuum table
baccus61
2005-08-14 05:56:49 UTC
Re: Vacuum table
hippodan
2005-08-14 08:36:53 UTC
Re: Vacuum table
turbulatordude
2005-08-14 10:54:48 UTC
Re: Vacuum table
davegsc@t...
2005-08-14 12:22:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: Vacuum table
Denis Casserly
2005-08-14 18:29:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum table
turbulatordude
2005-08-14 19:14:23 UTC
Re: Vacuum table
Aahz.
2005-08-14 20:16:56 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum table
caedave
2005-08-15 01:41:08 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum table
Marv Frankel
2005-08-15 02:31:46 UTC
Re: Vacuum table
notoneleft
2005-08-15 06:57:32 UTC
Re: Vacuum table
R Rogers
2005-08-15 07:17:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum table
Aahz.
2005-08-15 08:06:50 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum table
John Johnson
2005-08-15 18:12:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum table
wanliker@a...
2005-08-15 18:33:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum table
turbulatordude
2005-08-15 18:47:50 UTC
Re: Vacuum table - drag cutter
Andrey Lipavsky
2005-08-15 18:52:50 UTC
RE: [CAD_CAM_EDM_DRO] Re: Vacuum table
wanliker@a...
2005-08-15 18:56:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum table
John Johnson
2005-08-16 06:24:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum table - drag cutter
Ron Ginger
2005-08-16 06:49:38 UTC
Re:Vacuum table
Russ Waters
2005-08-16 07:33:19 UTC
Re: [CAD_CAM_EDM_DRO] Re:Vacuum table....No vacuum need for most applications!
Andrey Lipavsky
2005-08-16 07:36:59 UTC
RE: [CAD_CAM_EDM_DRO] Re: Vacuum table