Re: Worry, servo back powering Gecko
Posted by
mariss92705@y...
on 2001-07-16 14:37:52 UTC
Hi,
You don't have to worry at all unless you can turn the handwheels
more rapidly than the servo can at full speed.
Mariss
You don't have to worry at all unless you can turn the handwheels
more rapidly than the servo can at full speed.
Mariss
--- In CAD_CAM_EDM_DRO@y..., "Roger Swift" <vrsculptor@h...> wrote:
> When I manually position my servo mill (Tree Journeyman 350) with
power off
> the servos generate enough power to light up the Gecko 340's fault
lights.
> The table servos are large (rated 20 amps @ 90 volts) and connected
through
> a 3:1 reduction. The mill has both hand wheels and servos.
>
> Do I need to worry about frying the Gecko's? Do I need to put in a
relay
> between the Gecko and motor or remove the hand wheels?
>
> Roger
>
>
> _________________________________________________________________
> Get your FREE download of MSN Explorer at http://explorer.msn.com
Discussion Thread
Roger Swift
2001-07-16 14:23:16 UTC
Worry, servo back powering Gecko
mariss92705@y...
2001-07-16 14:37:52 UTC
Re: Worry, servo back powering Gecko
Jon Elson
2001-07-16 21:49:00 UTC
Re: [CAD_CAM_EDM_DRO] Worry, servo back powering Gecko
Alan Marconett KM6VV
2001-07-17 12:10:37 UTC
Re: [CAD_CAM_EDM_DRO] Worry, servo back powering Gecko
mariss92705@y...
2001-07-17 12:35:46 UTC
Re: Worry, servo back powering Gecko
Ron Yost
2001-07-17 13:28:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
mariss92705@y...
2001-07-17 13:36:53 UTC
Re: Worry, servo back powering Gecko
Alan Marconett KM6VV
2001-07-17 14:02:18 UTC
Re: Worry, servo back powering Gecko
Alan Marconett KM6VV
2001-07-17 14:26:44 UTC
Re: Worry, servo back powering Gecko
mariss92705@y...
2001-07-17 14:50:05 UTC
Re: Worry, servo back powering Gecko
Alan Marconett KM6VV
2001-07-17 15:46:34 UTC
Re: Worry, servo back powering Gecko
Jon Elson
2001-07-17 22:24:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
thscarince@h...
2001-07-18 06:07:45 UTC
Re: Worry, servo back powering Gecko
Larry Van Duyn
2001-07-18 07:04:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
Alan Marconett KM6VV
2001-07-18 10:57:46 UTC
Re: Worry, servo back powering Gecko
Ian Wright
2001-07-18 15:56:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
Tom Eldredge
2001-07-19 04:18:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
Garry & Maxine Foster
2001-07-20 17:26:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
Ian Wright
2001-07-21 01:57:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko