Re: Worry, servo back powering Gecko
Posted by
Alan Marconett KM6VV
on 2001-07-17 14:02:18 UTC
Hi Ron,
Well, a little I guess! Not a lot of torque, and I don't know if they
would skip steps, especially as there is no external power, as in a
Selsyn. At least you wouldn't have the 400 cycle buzz to put up with!
Selsyns are neat. I haven't played with them since the NAVY.
Perhaps they just need a little power? We used to use Selsyns for
antenna direction reports, Ham Radio satellites. I have been known to
SPIN 2 meter/440 Mhz beams with #34 stepper motors (RDF)!
Alan KM6VV
Ron Yost wrote:
Well, a little I guess! Not a lot of torque, and I don't know if they
would skip steps, especially as there is no external power, as in a
Selsyn. At least you wouldn't have the 400 cycle buzz to put up with!
Selsyns are neat. I haven't played with them since the NAVY.
Perhaps they just need a little power? We used to use Selsyns for
antenna direction reports, Ham Radio satellites. I have been known to
SPIN 2 meter/440 Mhz beams with #34 stepper motors (RDF)!
Alan KM6VV
Ron Yost wrote:
>
> Does this effect mean they can be used as Selsyns? That'd be useful
> for 'synching' two machines together???.
>
> Ron Yost .. looking in the stash for a couple of old SloSyn's to try it.
>
Discussion Thread
Roger Swift
2001-07-16 14:23:16 UTC
Worry, servo back powering Gecko
mariss92705@y...
2001-07-16 14:37:52 UTC
Re: Worry, servo back powering Gecko
Jon Elson
2001-07-16 21:49:00 UTC
Re: [CAD_CAM_EDM_DRO] Worry, servo back powering Gecko
Alan Marconett KM6VV
2001-07-17 12:10:37 UTC
Re: [CAD_CAM_EDM_DRO] Worry, servo back powering Gecko
mariss92705@y...
2001-07-17 12:35:46 UTC
Re: Worry, servo back powering Gecko
Ron Yost
2001-07-17 13:28:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
mariss92705@y...
2001-07-17 13:36:53 UTC
Re: Worry, servo back powering Gecko
Alan Marconett KM6VV
2001-07-17 14:02:18 UTC
Re: Worry, servo back powering Gecko
Alan Marconett KM6VV
2001-07-17 14:26:44 UTC
Re: Worry, servo back powering Gecko
mariss92705@y...
2001-07-17 14:50:05 UTC
Re: Worry, servo back powering Gecko
Alan Marconett KM6VV
2001-07-17 15:46:34 UTC
Re: Worry, servo back powering Gecko
Jon Elson
2001-07-17 22:24:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
thscarince@h...
2001-07-18 06:07:45 UTC
Re: Worry, servo back powering Gecko
Larry Van Duyn
2001-07-18 07:04:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
Alan Marconett KM6VV
2001-07-18 10:57:46 UTC
Re: Worry, servo back powering Gecko
Ian Wright
2001-07-18 15:56:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
Tom Eldredge
2001-07-19 04:18:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
Garry & Maxine Foster
2001-07-20 17:26:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko
Ian Wright
2001-07-21 01:57:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Worry, servo back powering Gecko