Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Posted by
Mike Gann
on 2001-07-19 19:02:19 UTC
Allen -
Some have taken 5 volts off an unused drive connector on the
power supply. Others have taken it off the game port.
Go to http://www.cnckits.com and click on the pBreak link.
This will take you to a page with a pin out of the game port.
Mike
allan_r9@... wrote:
Some have taken 5 volts off an unused drive connector on the
power supply. Others have taken it off the game port.
Go to http://www.cnckits.com and click on the pBreak link.
This will take you to a page with a pin out of the game port.
Mike
allan_r9@... wrote:
>
> Hello List,
>
> I'm getting close to connecting my EMC machine to my current mill,
> and ran into some problems connecting my Gecko 201s to the parallel
> port. Geckos require step/dir/+5VDC signal inputs, but the parallel
> port doesn't have +5VDC output, right? How are others making the
> connection to Geckos, specifcally supplying the +5VDC input? I will
> be getting a separate parallel port card to protect my motherboard.
> Will the BDI EMC install recognize a second parallel port card? What
> steps are required to "see" the additional port? Does the BDI
> install have a preference between PCI or ISA parallel port cards? I
> am trying to run the 5 axis EMC that Ian Wright supplied, so the
> total of 5 Geckos require a minumum of 80mA sink capability on the
> card(s).
> Any help or thoughts will be appreciated.
> Thank you,
> Allan
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
allan_r9@h...
2001-07-19 18:53:06 UTC
EMC/Gecko/Parallel Port interface
Mike Gann
2001-07-19 19:02:19 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Alan Marconett KM6VV
2001-07-19 19:36:08 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Jon Elson
2001-07-19 22:15:32 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Ian Wright
2001-07-20 02:30:14 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Jon Elson
2001-07-20 10:24:46 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Alan Marconett KM6VV
2001-07-20 12:58:30 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Ian Wright
2001-07-20 14:26:10 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Alan Marconett KM6VV
2001-07-20 14:40:26 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Paul
2001-07-20 16:10:19 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Alan Marconett KM6VV
2001-07-20 18:09:40 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Jon Elson
2001-07-20 20:20:42 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Ian Wright
2001-07-21 01:52:30 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Paul
2001-07-21 03:07:47 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Alan Marconett KM6VV
2001-07-21 10:53:55 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Ian Wright
2001-07-21 11:39:45 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Alan Marconett KM6VV
2001-07-21 12:09:11 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Alan Marconett KM6VV
2001-07-21 12:20:18 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Ian Wright
2001-07-21 13:36:47 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface
Alan Marconett KM6VV
2001-07-21 15:09:16 UTC
Re: [CAD_CAM_EDM_DRO] EMC/Gecko/Parallel Port interface