RE: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
Posted by
Gail & Bryan Harries
on 2001-07-26 10:30:21 UTC
Mark,
FYI: #3 Morse Taper w/drawbar is a fairly common Mill/Drill spindle format
in Asian equipment... the drawbar is to stop the taper letting go when doing
interrupted cuts... I have a Herless (Asian import into OZ) with this
setup... works just fine and is convenient for quick change to MT shanked
drill bits... downside, the taper is susceptible to jamming if the drawbar
is over tightened...
Bryan
-----Original Message-----
From: MARKEHLE [mailto:markehle@...]
Sent: Thursday, 26 July, 2001 11:10 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
Scott, Bryan -
No, I am really not sure what it is. It does look like morse, but I was not
aware that you could have morse with a drawbar.
Thanks for the web site - I now will be able to pin it down.
Mark
FYI: #3 Morse Taper w/drawbar is a fairly common Mill/Drill spindle format
in Asian equipment... the drawbar is to stop the taper letting go when doing
interrupted cuts... I have a Herless (Asian import into OZ) with this
setup... works just fine and is convenient for quick change to MT shanked
drill bits... downside, the taper is susceptible to jamming if the drawbar
is over tightened...
Bryan
-----Original Message-----
From: MARKEHLE [mailto:markehle@...]
Sent: Thursday, 26 July, 2001 11:10 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
Scott, Bryan -
No, I am really not sure what it is. It does look like morse, but I was not
aware that you could have morse with a drawbar.
Thanks for the web site - I now will be able to pin it down.
Mark
----- Original Message -----
From: "Scott M. Thomas" <scott@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, July 26, 2001 11:11 AM
Subject: RE: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
> I have a machine that uses Morse taper with a 3/8" drawbar. Are you sure
> its not Morse?
>
> -----Original Message-----
> From: Mark Ehle [mailto:markehle@...]
> Sent: Thursday, July 26, 2001 8:18 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
>
>
> Hello, All -
>
> I have just inherited a Millwaukee #2 horizontal mill. Instead of a #40 or
> #50 taper, it has a longer, smaller-diameter taper that looks like a morse
> taper, but has a drawbar hole in the tooling that did come with it. The
> gentleman that owned it said it was Brown and Sharp, but was not sure.
Would
> anybody be able to tell me for sure what it might be?
>
> I am looking for some end mill adapters and Morse-to-B&S adapters. Where
can
> I find these parts?
>
> Thanks!
>
> Mark Ehle
>
> Dowling, MI
>
>
> NetZero Platinum
> No Banner Ads and Unlimited Access
> Sign Up Today - Only $9.95 per month!
> http://www.netzero.net
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
>
NetZero Platinum
No Banner Ads and Unlimited Access
Sign Up Today - Only $9.95 per month!
http://www.netzero.net
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
Mark Ehle
2001-07-26 06:44:51 UTC
B&S Taper (off topic a little bit)
Scott M. Thomas
2001-07-26 08:12:37 UTC
RE: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
Gail & Bryan Harries
2001-07-26 08:44:14 UTC
RE: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
MARKEHLE
2001-07-26 09:37:18 UTC
Re: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
Gail & Bryan Harries
2001-07-26 10:30:21 UTC
RE: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
Jon Elson
2001-07-26 10:32:56 UTC
Re: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
Jon Elson
2001-07-26 10:54:33 UTC
Re: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
Smoke
2001-07-26 11:52:07 UTC
Re: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
ptengin@a...
2001-07-26 13:11:54 UTC
Re: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
jesse
2001-07-26 14:37:46 UTC
Re: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
MARKEHLE
2001-07-26 18:18:06 UTC
Re: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)
Garry & Maxine Foster
2001-07-26 19:02:12 UTC
RE: [CAD_CAM_EDM_DRO] B&S Taper (off topic a little bit)