CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] "nice numbers" for lead, window EMC dual boot, and the gotcha's

on 2001-08-13 00:31:41 UTC
Has anyone tried a homebrew imitation of Moglice? Did it work? What was
used? I would be really interested in finding out.

B



-----Original Message-----
From: Doug Harrison [mailto:prototype@...]
Sent: 13 August 2001 00:22
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] "nice numbers" for lead, window EMC dual
boot, and the gotcha's


David;
I'm told the 13/64 pitch is a misprint and that the 5/8" ballscrew is really
the standard .200 pitch that Thomson and Rockford sell.

If you want preload I would suggest contacting Rockford Ballscrew. Their
preloaded 5/8" nut is about $170 and it comes with the flange and wipers.
Buying two nuts, flange and wipers separately will set you back about the
same amount and you will still have to cobble up a preload mechanism.

The bearing end supports are a ripoff - much like buying ten foot sections
of rain gutter for $2.79 then having to pay $4.79 for the connectors. They
are easy to make using tapered roller bearings. Cheap wheel bearings from a
parts house work fine. The axial error will be significantly less than the
drunkenness of the rolled screws anyway.

An alternative to ballscrews is to use good acme screws and cast the nuts
using Moglice or some home brew imitation. If you are going to put these on
an Enco XY table this is probably all you really need.

Doug


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

David E. Queen 2001-08-12 13:41:15 UTC "nice numbers" for lead, window EMC dual boot, and the gotcha's Jon Elson 2001-08-12 15:39:18 UTC Re: [CAD_CAM_EDM_DRO] "nice numbers" for lead, window EMC dual boot, and the gotcha's Doug Harrison 2001-08-12 16:08:53 UTC Re: [CAD_CAM_EDM_DRO] "nice numbers" for lead, window EMC dual boot, and the gotcha's Paul 2001-08-12 16:40:25 UTC Re: [CAD_CAM_EDM_DRO] "nice numbers" for lead, window EMC dual boot, and the gotcha's daque@s... 2001-08-12 20:43:51 UTC Re: "nice numbers" for lead, window EMC dual boot, and the gotcha's Dr Brian H Le Page 2001-08-13 00:31:41 UTC RE: [CAD_CAM_EDM_DRO] "nice numbers" for lead, window EMC dual boot, and the gotcha's Larry Van Duyn 2001-08-13 05:50:25 UTC Re: [CAD_CAM_EDM_DRO] Re: "nice numbers" for lead, window EMC dual boot, and the gotcha's Dan Mauch 2001-08-13 07:28:26 UTC RE: [CAD_CAM_EDM_DRO] "nice numbers" for lead, window EMC dual boot, and the gotcha's Tim 2001-08-13 08:48:39 UTC RE: [CAD_CAM_EDM_DRO] "nice numbers" for lead, window EMC dual boot, and the gotcha's Joel Jacobs 2001-08-13 11:18:05 UTC Re: [CAD_CAM_EDM_DRO] "nice numbers" for lead, window EMC dual boot, and the gotcha's