CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Gecko drives

Posted by Tim Goldstein
on 2001-09-14 23:13:50 UTC
The switches will actually connect to the parallel port of the computer for
most controller programs. If you use one of the break out boards then yes
they just hook to the proper terminal which plugs them into the port.

Tim
[Denver, CO]

-----Original Message-----
From: georgedevogel@... <georgedevogel@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com <CAD_CAM_EDM_DRO@yahoogroups.com>
Date: Friday, September 14, 2001 11:15 PM
Subject: [CAD_CAM_EDM_DRO] Re: Gecko drives


>Hi Tim,
>
>You mean all I need to do is to wire the switches to the terminals
>that link to the computer? Is there any website where I can view the
>wiring diagram?
>
>Thanks. You guys have been very helpful
>
>George
>
>
>--- In CAD_CAM_EDM_DRO@y..., "Tim Goldstein" <timg@k...> wrote:
>> Bipolar will give you more torque from a given motor which is
>particularly
>> useful at higher motor speeds. Really no downside to bipolar other
>than that
>> they generally cost more.
>>
>> Home & limit switches don't hook directly to the drive, but to the
>computer
>> that is directing them. The power supply hookup to a Gecko is very
>straight
>> forward Power supply + to the + terminal, power supply - to the -
>terminal.
>>
>> Tim
>> [Denver, CO]
>>
>> > -----Original Message-----
>> >
>> >
>> > Hi,
>> >
>> > I am new to electronics and CNC and is hoping to construct a
>stepper
>> > motor drive and is trying to decide between a kit like the one
>> > available from hobbycnc, but I hear so much about the Gecko.
>> >
>> > For the moment, I am leaning towards the kit from hobbycnc, but I
>was
>> > told it is unipolar, and it seems that the bipolar drivers are
>better
>> > or something. But is is convenient, I think, because it include
>power
>> > supply, limit and home switches, etc.
>> >
>> > I know that with the Gecko, one will have to add the power supply,
>> > but what about the home switches and limit switches? How do I get
>> > information and circuit diagrams on how to add the power supply
>and
>> > home, limit switches for the Gecko?
>> >
>> > Thanks
>> >
>> > George
>> >
>> >
>> > Addresses:
>> > FAQ: http://www.ktmarketing.com/faq.html
>> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>

Discussion Thread

lcasey@b... 2000-10-17 16:56:02 UTC Gecko drives Bob Campbell 2000-10-17 18:08:18 UTC Re: [CAD_CAM_EDM_DRO] Gecko drives georgedevogel@y... 2001-09-14 18:51:16 UTC Gecko drives Carol & Jerry Jankura 2001-09-14 19:08:46 UTC RE: [CAD_CAM_EDM_DRO] Gecko drives Tim Goldstein 2001-09-14 19:09:30 UTC RE: [CAD_CAM_EDM_DRO] Gecko drives Bob Campbell 2001-09-14 19:17:38 UTC Re: [CAD_CAM_EDM_DRO] Gecko drives georgedevogel@y... 2001-09-14 22:07:42 UTC Re: Gecko drives georgedevogel@y... 2001-09-14 22:12:23 UTC Re: Gecko drives georgedevogel@y... 2001-09-14 22:15:00 UTC Re: Gecko drives Doug Fortune 2001-09-14 22:54:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko drives Tim Goldstein 2001-09-14 23:13:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko drives wanliker@a... 2001-09-15 00:03:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko drives machines@n... 2001-09-15 01:27:16 UTC Re: Gecko drives georgedevogel@y... 2001-09-15 10:52:53 UTC Re: Gecko drives georgedevogel@y... 2001-09-15 11:03:04 UTC Re: Gecko drives HighTech 2001-09-15 12:21:11 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko drives Tim Goldstein 2001-09-15 13:44:56 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko drives